Manuals / Intel / Computer Equipment / Server

Intel SE7500CW2 manual Installation Procedures, Installing the I/O Gasket and Shield

Models: SE7500CW2

1 92

Download 92 pages 39.44 Kb

Page 50

Image 50

Installation Procedures

Installing the I/O Gasket and Shield

✏NOTE

An ATX 2.03-compliant I/O shield is provided with the server board. The shield is required by Electromagnetic Interference (EMI) regulations to minimize EMI. If the shield does not fit the chassis, obtain a properly sized shield from the chassis supplier.

The shield fits the rectangular opening in the back of a chassis. The shield has cutouts that match the I/O ports. Install the shield from inside the chassis.

Attaching the Gasket to the I/O Shield

1.Remove the two backing strips from the gasket.

2.Press the gasket onto the inside face of the I/O shield as shown.

OM14074

Figure 3. Attaching the Gasket to the I/O Shield

50	Intel Server Board SE7500CW2 Product Guide

Page 50

Image 50

Intel SE7500CW2 Installation Procedures, Installing the I/O Gasket and Shield, Attaching the Gasket to the I/O Shield

Contents

Subassemblies/Products Intel Server Board SE7500CW2 Product GuideDisclaimer Server Board Installation Contents2 Configuration Software and Utilities DescriptionSolving Problems UpgradingIndex Technical Reference8 Regulatory and Integration Information FiguresTables Table 1. Server Board Features Server Board Features1 Description FeatureDescription Table 1. Server Board Features continuedFeature E A B CD F G Back Panel ConnectorsFigure 1. Back Panel Connectors OM14419BB AA Z Y X W V U TS Server Board Connector and Component LocationsA B C D E F G H I J K L M N O R Q PBoxed Processor Fan Heat sink ProcessorDual Processor Operation Intel E7500 Chipset ICH3Serial Ports Keyboard and Mouse ConnectorsSuper I/O Parallel PortMemory PCI I/O Subsystem64-bit /133 MHz PCI-XCapable Subsystem 64-bit /100 MHz PCI-XCapable SubsystemNetwork Interface Controller NIC Supported Network FeaturesVideo Controller 32-bit/33MHz PCI SubsystemWake on LAN ACPIAC Link Mode Password Protection SecurityPassword Clear Jumper Using PasswordsIntel Server Board SE7500CW2 Product Guide 2 Configuration Software and Utilities Power-On Self-TestPOSTStarting Setup Using BIOS Setup UtilityIf You Cannot Access Setup Setup MenusDescription Keyboard CommandsPress Menu Selection Bar Main Menu Table 7. Main MenuPrimary/Secondary, Master/Slave Submenus Table 8. Primary/Secondary, Master/Slave SubmenuAdvanced Menu Table 9. Advanced MenuDOS default FeatureDisabled default No default Auto Detect defaultI/O Device Configuration Submenu Table 10. I/O Device Configuration SubmenuIRQ7 default FeatureECP default 378 default DMA 3 defaultOn Board Device Submenu Table 11. On Board Device SubmenuPCI Configuration Submenu Table 12. PCI Configuration SubmenuTable 14. Server Menu Submenu Server Menu SubmenuTable 13. Option ROM Scan Submenu Console Redirection Submenu Table 15. Console Redirection SubmenuEvent Logging Submenu Table 16. Event Logging SubmenuHardware Monitor Submenu Table 17. Hardware Monitor SubmenuSecurity Menu Table 18. Security MenuPower Menu Boot MenuDevice Table 20. Boot MenuBoot Priority DescriptionSystem Menu Table 21. System MenuTable 22. Exit Menu Exit MenuTable 21. System Menu continued Recording the Current BIOS Settings Upgrading the BIOSPreparing for the Upgrade Obtaining the Upgrade UtilityCreating the BIOS Upgrade Diskette Upgrading the BIOSRecovering the BIOS Changing the BIOS Language Hardware Monitoring Table 23. Monitored Headers and SensorsIntel Server Board SE7500CW2 Product Guide Tools and Supplies Needed 3 Server Board InstallationSafety Cautions Before You BeginSafety and Regulatory Compliance Intel Server Board SE7500CW2 Product GuideMinimum Hardware Requirements Installation NotesPower Supply ProcessorAttaching the Gasket to the I/O Shield Installation ProceduresInstalling the I/O Gasket and Shield Figure 5. Installing the I/O Shield Installing the I/O ShieldAttaching the Label to the I/O Shield Figure 4. Attaching the Label to the I/O ShieldConfiguring Chassis Standoffs Installing Rubber Bumpers Attaching the Server Board Installing the Server BoardPlacing the Server Board into the Chassis Installing Memory Figure 10. Installing MemoryInstalling the Processors Installing the Retention BracketsAttaching the Processor Applying Thermal GreaseAttaching the Heat Sink Installing the Processor Wind TunnelAttaching the Processor Wind Tunnel Assembly Figure 16. Attaching the Heat Sink Fan Attaching the Heat Sink FanAttaching Intake and Exhaust Assemblies Installing the Optional SCSI Add-inCard Making Connections to the Server Board Figure 18. Making Connections to the Server BoardCable Routing IDE CablesOM14421 Floppy Drive CableFigure 20. Routing the Floppy Drive Cable Finishing Up Tools and Supplies Needed 4 UpgradingCautions CAUTIONSMemory Figure 22. Installing DIMMsUpgrading ProcessorsCAUTIONS Figure 23. Installing the Retention Brackets Adding or Replacing a ProcessorInstalling the Retention Brackets 1. Lift the socket lever on the processor Attaching the ProcessorApplying Thermal Grease Figure 27. Attaching the Wind Tunnel Assembly Installing the Processor Wind TunnelAttaching the Processor Wind Tunnel Assembly Attaching the Heat Sinkby side Attaching the Heat Sink FanAttaching Intake and Exhaust Assemblies ADVARSEL Replacing the Backup BatteryRemoving a Processor ADVARSELVARNING VAROITUSIntel Server Board SE7500CW2 Product Guide Checklist 5 Solving ProblemsResetting the System Initial System StartupChecklist Running New Application SoftwareAfter the System Has Been Running Correctly ChecklistMonitoring POST More Problem Solving ProceduresPreparing the System for Diagnostic Testing Verifying Proper Operation of Key System Lights Specific Problems and Corrective ActionsPower Light Does Not Light Confirming Loading of the Operating SystemNo Characters Appear on Screen Characters Are Distorted or IncorrectSystem Cooling Fans Do Not Rotate Properly Diskette Drive Activity Light Does Not LightDiagnostics pass but the connection fails Problems with NetworkThe server hangs when the drivers are loaded Hard Disk Drive Activity Light Does Not LightPCI Installation Tips Problems with Application SoftwareBootable CD-ROMIs Not Detected Telephone 6 Getting HelpWorld Wide Web In U.S. and CanadaIntel Server Board SE7500CW2 Product Guide Figure 31. Configuration Jumper Location Configuration Jumpers7 Technical Reference Table 24. Configuration Jumper J106Figure 32. Front Panel Header Connection Location Front Panel HeaderPins Front Panel Header Connection DescriptionsProduct Regulatory Compliance Product Safety Compliance8 Regulatory and Integration Information Product EMC ComplianceFCC USA Electromagnetic Compatibility NoticesProduct Regulatory Compliance Markings Taiwan Declaration of Conformity INDUSTRY CANADA ICES-003Europe CE Declaration of Conformity Intel Server Board SE7500CW2 Product Guide Korean RRL ComplianceAustralia / New Zealand Index