Juniper Networks 8 Cabling ERX Routers

Chapter 5

Cabling ERX Routers

This chapter describes how to cable an ERX router. Before you cable the router,

ensure that you have completed all installation instructions identified in previous

chapters.

This chapter contains the fol lowing sections:

Cabling Overview on page 53

RequiredTools, Wires, and Cables on page 55

Cabling the SRP I/O Module on page 56

Cabling the Router forPower on page 60

Cabling I/O Modules on page 66

The Next Step on page 72

Cabling Overview

Cabling an ERX router requires the following main tasks:

1. Familiarizeyourself with the module ports, and ensure that you have the cables

and wires needed to complete each cabling procedure. (See Figure 23.)

2. Read and understand all safety warnings. (See “Installation Guidelines and

Requirements” on page 129.)

3. (Optional) Connect timing ports.

4. Connect the SRP I/O module to the network and to a management console.

5. Connect grounding wiresto the router chassis.

6. Connect the power cables fromthe power source to the power input module.

7. Connect the line I/O modules to their appropriate network interface.

Cabling Overview 53

Contents

Main E-series Routing Platforms ERX Hardware Guide Release 8.0.x Page End User License Agreement Page Table of Contents Part 1 Product Overview Part 2 Initial Installation Page Part 3 Hardware Maintenance, Replacement, and Troubleshooting Procedures Part 4 Appendixes Part 5 Index About This Guide Objectives Audience E-series Routers Documentation Conventions Convention Description Examples List of Technical Publications Table3: Juniper Networks E-series and JUNOSe TechnicalPublications xiv Page xvi Obtaining Documentation Documentation Feedback Requesting Support Page Page Chapter 1 ERX Overview Overview ERX Routers ERX-14xx Models Figure 1: ERX-14xx Models, Front View ERX-7xx Models Page ERX-310 Router ERX Modules SRP Module Figure 9: SRP Module for ERX-7xx and ERX-14xx Models Module Details SRP Module Redundancy Nonvolatile Storage SRP I/O Module Module Details Line Modules Packet Classification I/O Modules Network Management Tools CLI Management SNMP MIB Management NMC-RX Device Management System Redundancy Features NVS Cards Line Modules Page Power Fans Part 2 Initial Installation Page Chapter 2 Unpacking and Inspecting ERX Routers Before You Begin Unpacking ERX-14xx Models Unpacking ERX-7xx Models and ERX-310 Routers Inspecting Router Components and Accessories If You Detect or Suspect Damage Contacting Juniper Networks Page Chapter 3 Installing ERX Routers Before You Begin Freestanding Installation Rack-Mounted Installation Installation Guidelines Page Page Page Preparing the Equipment Racks Installing the Router Page Page Chapter 4 Installing Modules Overview Slot Groups Slot Groups for the ERX-1410 Router Figure 17: ERX-1410 Slot Groups Slot Groups for the ERX-7xx Models Figure18: ERX-7xx Model Slot Groups Page Page Order of Installation Required Tools and Safety Items Installing SRP I/O and SRP Modules Installing an SRP I/O Module Installing an SRP Module Page Installing Line and I/O Modules Installing a Line Module or an I/O Module Page Removing a Line Module, SRP Module, or SRP I/O Module Page Installing Components for Line Module Redundancy Installing theLineModules Installing the Redundancy Midplane Page Installing the I/O Modules Page Page Chapter 5 Cabling ERX Routers Cabling Overview NOTE: Werecommend that you use shielded cables where appropriate. Figure 23: ERX Ports and Connectors (ERX-14xx Model Shown) 54 Required Tools, Wires, and Cables Cabling the SRP I/O Module External Timing Ports Page ERX 8.0.x Hardware Guide Figure 24: SRP I/O Module for ERX-14xx Models CONSOLE DB-9 To con nectthe clock source input ports: 1. Depending on the connectortype, complete one of the following tasks: 58 Management Ports Connecting to the Network Connecting to a Console Terminal Cabling the Router for Power Table9: Power Input Module Cables and Wires Needed Cable/Wire From To ERX 8.0.x Hardware Guide Figure 26: Power Input Module for ERX-14xx Models Ground Power A leads ! Power input module cover 62 Task 1: Turn Off All Router Power Task 2: Connect the Grounding Cables Task 3: Connect the Power Cables ERX-7xx Models, ERX-14xx Models, ERX-310 Router (DC Model) Page Figure 27: ERX-310 Router, Rear View (DC Model) ERX-310 Router (AC Model) NOTE: Toprovide redundancy, do not terminate PowerA and Power B leads at the same power source. Cabling I/O Modules BNC Connectors HSSI Connectors Cabling ERX Routers Figure 30: HSSI I/O Module with 50-Pin HSSI Connector RJ-45 Connectors When inserting an RJ-45 connector, be sure it clicks into the port. Figure 31: I/O Module with RJ-45 Connector Port 0 RJ-48C Connectors LC Duplex Connectors SC Duplex Connectors Page Figure 33: I/O Module with SC Full Duplex Connectors SMB Connectors 70 X.21/V.35 Connectors Redundant Ports Chapter 6 Powering Up ERX Routers Before You PowerUp the System Powering Up Initialization Sequence Status LEDs Powering Down Page Chapter 7 Accessing ERX Routers Setting Up Management Access Console Port Setup Using HyperTerminal Connecting Directly to the Router Page Assigning an IP Address Telne t Setup Page SNMP Page Page Chapter 8 Maintaining ERX Routers Required Tools and Items Storing Modules and Components Cleaning the System Upgrading from Release 5.1.1 or Lower-Numbered Releases to Release 6.x.x or Higher-Numbered Releases Upgrading NVS Cards on SRP Modules Upgrading a System That Contains One SRP Module Upgrading a System That Contains Two SRP Modules Replacing an NVS Card Upgrading Memory on SRP Modules Displaying the Memory Installed Removing SODIMMs Adding New SODIMMs To add new SODIMMs: 92 1. Locate the four SODIMM sockets on the SRP module. (See Figure 38 and Figure 39.) See the previous section to learn how to remove SODIMMs. Verify ing the Upgr ade Replacing SFPs on I/O Modules Removing SFPs Installing SFPs Page Verify ing the Inst allation Replacing FanTrays Page Removing the Fan Tray Installing the Fan Tray Installing a Cable-Management Bracket on ERX-7xx Models Figure 46: Attaching a Cable Management Bracket Page Chapter 9 Troubleshooting Diagnosing Problems Initialization Sequence Troubleshooting Power Failures 104 Table 10: Causes of Power Failures Symptom Possible Problems Actions 1. 2. LED Identification 106 Page Page Troubleshooting Figure 48: FE2 Module LEDs Understanding Status LEDs to Troubleshoot 109 Functional status LEDs Interface status LEDs g013769 LED Activity 110 Table12: Normal Activity of Functional Status LEDS During Booting OK FAIL ONLINE Status Process Table13: Troubleshooting Abnormal LED Activity on Modules Diagnostic Signs Possible Problems Actions 1. 2. 3. 4. 1. 112 Redundancy Status Monitoring Temperatures of Modules Resetting Line Modules and SRP Modules Double-Bit Errors on SRP Modules Detecting Double-Bit Errors Fixing Double-Bit Errors Page Page Page Appendix A System Specifications ERX-14xx Models Specifications Table 16: ERX-14xx Models Specifications 120 Page ERX-7xx Models Specifications Table 17: ERX-7xx Models Specifications 122 Page 124 ERX-310 Router Specifications Table 18: ERX-310 Router Specifications 126 Page Page Appendix B Installation Guidelines and Requirements Your Preinstallation Responsibilities Environmental Requirements Regulatory Compliances Page ERX-310 Router Warnings (AC Model) The following warningsapply only to the ERX-310 router. 132 ERX-310 Power Cord Warnings (AC Model) Power Cable Warning (Japanese) Equipment Rack Requirements Mechanical Requirements Space Requirements Proper Rack Installation Page Product Reclamation and Recycling Program Hardware Compliance Federal Communications Commission (FCC) Statement FCC Requirements for Consumer Products Food and Drug Administration, Center for Devices and Radiological Health Canadian Department Of Communications Radio Interference Regulations Rglement sur le brouillage radiolectrique du ministre des communications Industry Canada Notice CS-03 Avis CS-03 dIndustrie Canada D.O.C. Explanatory Notes: Equipment Attachment Limitations Notes explicatives du ministre des Communications: limites visant les accessoires EC Declaration of Conformity Voluntar y Control Council for Interference (VCCI) Statement for Japan Appendix C Cable Pinouts SRP I/O Module Page Page Table22 lists the pinout for the straight-through adapter. CT1 and CE1 I/O Modules 146 Page Figure 55: CE1 I/O Module with Telco Connectors CE1 I/O Figure 56: Twenty-Port Balun Panel 148 Table24andTable25listthepinoutsfortheTelcoconnectorsoneachcable. Table24: Pinout of 50-Pin TelcoConnector to Por ts 09 Table25: Pinout of 50-Pin TelcoConnector to Por ts1019 150 Appendix D Contacting Customer Support and Returning Hardware Contacting Customer Support Return Procedure Locating Component Serial Numbers Information You Might Need to Supply to JTAC Tools and Parts Required Returning Products for Repair or Replacement Packing Instructions for Returning a Chassis Page Page Appendix E Declaration of Conformity Declaration of Conformity on page 157 Declaration of Conformity Declaration of Conformity according to ISO/IEC Guide 22 and EN4514 Page Page Page Index Symbols A B C D E 162 F G I J L M N P Q 164 R S T U V W X