Obtaining Documentation | Juniper Networks 8 specification

About This Guide

Document	Description
JUNOSe Command Reference Guide	Together constitute the JUNOSe Command Reference Guide. Contain
A to M	important information about commands implemented in the system
JUNOSe Command Reference Guide N to Z	software. Use to look up:
JUNOSe Command Reference Guide N to Z
			Descriptions of commands and command parameters
			Descriptions of commands and command parameters
			Command syntax
			Command syntax
			A command’s related mode
			A command’s related mode
			Starting with JUNOSe Release 7.1.0, a history of when a
			Starting with JUNOSe Release 7.1.0, a history of when a
			command, its keywords, and its variables were introduced
			or added
	Use with the JUNOSe configuration guides.

JUNOSe Comprehensive Index	Provides a complete index of the JUNOSe software documentation set.

Release Notes

JUNOSe Release Notes	Provide the latest information about features, changes, known
	problems, resolved problems, and system maximum values. If the
	information in the Release Notes differs from the information found in
	the documentation set, follow the Release Notes .
	Release notes are included on the corresponding software CD and
	are available on the Web.

Obtaining Documentation

To obtain the most current version of all Juniper Networks technical documentation, see the products documentation page on the Juniper Networks Web site at http://www.juniper.net/.

To order printed copies of this guide and other Juniper Networks technical documents, or to order a documentation CD, which contains this guide, contact your sales representative.

Copies of the Management Information Bases (MIBs) available in a software release are included on the documentation CDs and at http://www.juniper.net/.

Documentation Feedback

We encourage you to provide feedback, comments, and suggestions so that we can improve the documentation. You can send your comments to techpubs-comments@juniper.net, or fill out the documentation feedback form at http://www.juniper.net/techpubs/docbug/docbugreport.html. If you are using e-mail, be sure to include the following information with your comments:

Document name

Document part number

Documentation Feedback xvii

Image 17

Juniper Networks 8 manual Obtaining Documentation, Documentation Feedback

Contents

ERX Hardware Guide Series Routing Platforms ERX Hardware Guide, Release End User License Agreement Page Table of Contents Chapter Unpacking and Inspecting ERX Routers Part Initial Installation Chapter Cabling ERX Routers Part Procedures Part Appendixes Appendix a System Specifications Part Index Audience About This GuideObjectives Documentation Conventions Series RoutersIcon Meaning Description Convention Description Examples List of Technical Publications Issue the clock source Xiv JUNOSe Software Guides Xvi Documentation Feedback Obtaining Documentation Requesting Support Product Overview Product Overview ERX Routers ERX OverviewOverview ERX-14xx Models ERX-14xx Models, Front View ERX-14xx Models, Rear View ERX-7xx Models ERX-7xx Models, Front View ERX-310 Router, Front View AC Model ERX-310 Router ERX-310 Router, Rear View AC Model ERX Modules Modules in ERX-14xx Models SRP Module SRP Module for ERX-7xx and ERX-14xx Models Module Details SRP I/O Module SRP Module Redundancy Line Modules Representative Line Module Modules Network Management Tools Redundancy Features NVS Cards Shows the data flow when a spare line module becomes active Data Flow When a Spare Line Module Is Active Power Fans Initial Installation Initial Installation Unpacking ERX-14xx Models Unpacking and Inspecting ERX RoutersBefore You Begin Removing an L-Bracket Unpacking ERX-7xx Models and ERX-310 Routers If You Detect or Suspect Damage Inspecting Router Components and AccessoriesContacting Juniper Networks Next Step ERX 8.0.x Hardware Guide Next Step Freestanding Installation Installing ERX Routers Installation Guidelines Rack-Mounted Installation Installing ERX Routers ERX Routers Installed in Recommended Order Safety Guidelines Installing ERX Routers Rack-Mounted Installation Preparing the Equipment Racks Installing the Router Next Step ERX 8.0.x Hardware Guide Next Step Installing Modules Orientation of Line Modules in ERX Routers Slot Groups Slot Groups for the ERX-7xx Models Combinations of Line Modules In Slot Groups Managing Modules Using the SoftwareOC48 Line Modules GE-2 Line Modules Grounding Jack Locations Series Router Connecting the Wrist Strap to the ERX-310 Router Rear Safety Guidelines Order of InstallationRequired Tools and Safety Items SRP Module Slot Assignments Router Installing SRP I/O and SRP Modules Installing an SRP Module Installing an SRP I/O Module Ejectors in the Open Position Installing a Line Module or an I/O Module Installing Line and I/O Modules Module Slot Assignments Router Removing a Line Module, SRP Module, or SRP I/O Module Ejectors in the Closed Position Installing the Redundancy Midplane Installing Components for Line Module RedundancyInstalling the Line Modules Enter the halt command Installing a Redundancy Midplane Installing the I/O Modules Configuring Line Module Redundancy Verifying the Installation ERX 8.0.x Hardware Guide Next Step Cabling Overview Cabling ERX Routers ERX Ports and Connectors ERX-14xx Model Shown Required Cables Connection Port and Cable Used Required Tools, Wires, and Cables SRP I/O Ports Description Cabling the SRP I/O ModuleExternal Timing Ports Cabling ERX Routers SRP I/O Module for ERX-14xx Models SRP I/O Module for the ERX-310 Router Management Ports Cabling the Router for Power Connecting to the Network ERX-14xx models Power Input Module Cables and Wires Needed Cable/Wire From Power Input Module for ERX-14xx Models Task 1 Turn Off All Router Power Task 2 Connect the Grounding Cables Task 3 Connect the Power Cables ERX 8.0.x Hardware Guide ERX-310 Router AC Model Cabling I/O Modules BNC ConnectorsHssi Connectors RJ-48C Connectors RJ-45 Connectors SC Duplex Connectors LC Duplex Connectors Class 1 LED Product O Module with SC Full Duplex Connectors SMB Connectors O Module with SMB Connectors 21/V.35 Connectors Redundant Ports 21/V.35 Module with 50-Pin X.21/V.35 Connector Powering Up Powering Up ERX RoutersBefore You Power Up the System Initialization Sequence Status LEDs Powering Down ERX 8.0.x Hardware Guide Next Step Setting Up Management Access Accessing ERX Routers Connecting Directly to the Router Console Port SetupUsing HyperTerminal Management Ports for ERX Routers Assigning an IP Address Telnet Setup Enter the configure command Snmp Maintaining ERX Routers on Troubleshooting on Page Required Tools and Items Maintaining ERX Routers Storing Modules and Components Cleaning the System Upgrading a System That Contains One SRP Module Upgrading NVS Cards on SRP Modules Upgrading a System That Contains Two SRP Modules Replacing an NVS Card NVS Card Slot on SRP Module Upgrading Memory on SRP Modules Removing SODIMMs Displaying the Memory Installed Sodimm Sockets on the SRP-5 and SRP-10 Module Adding New SODIMMs Replacing SFPs on I/O Modules Verifying the Upgrade Possible Release Mechanisms on the SFP Removing SFPs Example of SFP Installing SFPs Installing an SFP on a GE I/O Module Replacing Fan Trays Fan Tray in ERX-14xx Models Removing the Fan Tray Installing the Fan Tray 100 Installing a Cable-Management Bracket on ERX-7xx Models 101 102 Diagnosing Problems Troubleshooting Understanding Status LEDs to Troubleshoot Troubleshooting Power FailuresCauses of Power Failures Symptom Possible Problems Actions Redundant LED Identification 106 107 SRP Module LEDs 109 LED Activity Normal Activity of Functional Status Leds During Booting Status Process Issue the reload slot slotnumber 112 Redundancy Status of a Line Module Monitoring Temperatures of ModulesRedundancy Status Detecting Double-Bit Errors Resetting Line Modules and SRP ModulesDouble-Bit Errors on SRP Modules Fixing Double-Bit Errors 116 Appendixes Appendixes ERX-14xx Models Specifications Category System SpecificationsERX-14xx Models Specifications Space Requirements Category Specification 121 ERX-7xx Models Specifications Category ERX-7xx Models Specifications 123 124 ERX-310 Router Specifications Category ERX-310 Router Specifications 126 127 128 Your Preinstallation Responsibilities Installation Guidelines Requirements Regulatory Compliances Environmental Requirements Installation Guidelines and Requirements Safety Guidelines ERX-310 Router Warnings AC Model ERX-310 Power Cord Warnings AC Model Equipment Rack Requirements Mechanical Requirements ERX Routers Installed in a Rack Space Requirements Proper Rack Installation Airflow for ERX Routers Cabling Recommendations Product Reclamation and Recycling Program Federal Communications Commission FCC Statement Hardware Compliance Industry Canada Notice CS-03 FCC Requirements for Consumer Products Avis CS-03 d’Industrie Canada C. Explanatory Notes Equipment Attachment Limitations EC Declaration of Conformity SRP I/O Module Cable Pinouts SRP I/O Module Serial Port SRP I/O Module-RS-232 Serial Connector Pinout Signal SRP I/O Module Ethernet Port SRP I/O Module-RJ-45 Connector Pinout Signal Lists the pinout for the straight-through adapter CT1 and CE1 I/O Modules CT1 I/O Module Ports CT1/CE1 I/O Module-RJ-48C Connector Pinout Signal Pinout of 50-Pin Telco Connector to Ports Signal CE1 I/O Module with Telco Connectors 149 Pin Signal 150 Contacting Customer Support Return ProcedureContacting Customer Support and Returning Hardware 152 Locating Component Serial Numbers Representative Module Serial Number ID Label Information You Might Need to Supply to Jtac Packing Instructions for Returning a Chassis Returning Products for Repair or ReplacementTools and Parts Required 155 156 Declaration of Conformity Declaration of Conformity 158 Index Index Accessing Symbols Series routers Modules QoS, packet classification for 21/V.35 connectors, cabling