CT1 and CE1 I/O Modules | Juniper Networks 8 guide

ERX 8.0.x Hardware Guide

Table 21: DB-9—RJ-45 Crossover Adapter Pinout

DB-9 Pin	Signal	RJ-45 Pin
1	DCD	1

2	RXD	3

3	TXD	2

4	DTR	6

5	GND	5

6	DSR	4

7	RTS	8

8	CTS	7

9	RNG	no connect

Table 22 lists the pinout for the straight-through adapter.

Table 22: DB-9—RJ-45 Straight-Through Adapter Pinout

	RS-232 Signal		Ethernet Signal
DB-9 Pin	Name	RJ-45 Pin	Name

1	DCD	1	TX +

2	RXD	2	TX –

3	TXD	3	RX +

4	DTR	4	no connect

5	GND (signal)	5	no connect

6	DSR	6	RX –

7	RTS	7	no connect

8	CTS	8	no connect

9	RNG	no connect	none

CT1 and CE1 I/O Modules

CT1 I/O modules have 24 RJ-48C female connectors. CE1 I/O modules have either

20RJ-48C female connectors or two 25-pair female Telco connectors. Figure 54 shows the location of the ports on a CT1 I/O module and the sequence of the pins in the RJ-48C connector. CE1 I/O modules equipped with RJ-48C connectors have the same configuration as CT1 I/O modules equipped with RJ-48C connectors.

146		CT1 and CE1 I/O Modules

Image 164

Juniper Networks 8 manual CT1 and CE1 I/O Modules, Lists the pinout for the straight-through adapter

Contents

ERX Hardware Guide Series Routing Platforms ERX Hardware Guide, Release End User License Agreement Page Table of Contents Part Initial Installation Chapter Unpacking and Inspecting ERX Routers Chapter Cabling ERX Routers Procedures Part Appendix a System Specifications Part Appendixes Part Index Audience About This GuideObjectives Series Routers Documentation ConventionsIcon Meaning Description Convention Description Examples Issue the clock source List of Technical Publications Xiv JUNOSe Software Guides Xvi Obtaining Documentation Documentation Feedback Requesting Support Product Overview Product Overview ERX Routers ERX OverviewOverview ERX-14xx Models ERX-14xx Models, Front View ERX-7xx Models ERX-14xx Models, Rear View ERX-7xx Models, Front View ERX-310 Router ERX-310 Router, Front View AC Model ERX Modules ERX-310 Router, Rear View AC Model SRP Module Modules in ERX-14xx Models SRP Module for ERX-7xx and ERX-14xx Models Module Details SRP Module Redundancy SRP I/O Module Line Modules Modules Representative Line Module Redundancy Features Network Management Tools NVS Cards Shows the data flow when a spare line module becomes active Power Data Flow When a Spare Line Module Is Active Fans Initial Installation Initial Installation Unpacking ERX-14xx Models Unpacking and Inspecting ERX RoutersBefore You Begin Unpacking ERX-7xx Models and ERX-310 Routers Removing an L-Bracket Inspecting Router Components and Accessories If You Detect or Suspect DamageContacting Juniper Networks Next Step ERX 8.0.x Hardware Guide Next Step Installing ERX Routers Freestanding Installation Rack-Mounted Installation Installation Guidelines Installing ERX Routers Safety Guidelines ERX Routers Installed in Recommended Order Installing ERX Routers Rack-Mounted Installation Installing the Router Preparing the Equipment Racks Next Step ERX 8.0.x Hardware Guide Next Step Installing Modules Slot Groups Orientation of Line Modules in ERX Routers Slot Groups for the ERX-7xx Models Managing Modules Using the Software Combinations of Line Modules In Slot GroupsOC48 Line Modules GE-2 Line Modules Connecting the Wrist Strap to the ERX-310 Router Rear Grounding Jack Locations Series Router Safety Guidelines Order of InstallationRequired Tools and Safety Items Installing SRP I/O and SRP Modules SRP Module Slot Assignments Router Installing an SRP I/O Module Installing an SRP Module Ejectors in the Open Position Installing Line and I/O Modules Installing a Line Module or an I/O Module Module Slot Assignments Router Removing a Line Module, SRP Module, or SRP I/O Module Ejectors in the Closed Position Installing the Redundancy Midplane Installing Components for Line Module RedundancyInstalling the Line Modules Enter the halt command Installing the I/O Modules Installing a Redundancy Midplane Verifying the Installation Configuring Line Module Redundancy ERX 8.0.x Hardware Guide Next Step Cabling ERX Routers Cabling Overview ERX Ports and Connectors ERX-14xx Model Shown Required Tools, Wires, and Cables Required Cables Connection Port and Cable Used SRP I/O Ports Description Cabling the SRP I/O ModuleExternal Timing Ports Cabling ERX Routers SRP I/O Module for ERX-14xx Models Management Ports SRP I/O Module for the ERX-310 Router Connecting to the Network Cabling the Router for Power Power Input Module Cables and Wires Needed Cable/Wire From ERX-14xx models Task 1 Turn Off All Router Power Power Input Module for ERX-14xx Models Task 3 Connect the Power Cables Task 2 Connect the Grounding Cables ERX 8.0.x Hardware Guide ERX-310 Router AC Model Cabling I/O Modules BNC ConnectorsHssi Connectors RJ-45 Connectors RJ-48C Connectors LC Duplex Connectors SC Duplex Connectors Class 1 LED Product SMB Connectors O Module with SC Full Duplex Connectors 21/V.35 Connectors O Module with SMB Connectors 21/V.35 Module with 50-Pin X.21/V.35 Connector Redundant Ports Powering Up Powering Up ERX RoutersBefore You Power Up the System Initialization Sequence Powering Down Status LEDs ERX 8.0.x Hardware Guide Next Step Accessing ERX Routers Setting Up Management Access Connecting Directly to the Router Console Port SetupUsing HyperTerminal Management Ports for ERX Routers Telnet Setup Assigning an IP Address Enter the configure command Snmp Maintaining ERX Routers on Troubleshooting on Page Maintaining ERX Routers Required Tools and Items Cleaning the System Storing Modules and Components Upgrading NVS Cards on SRP Modules Upgrading a System That Contains One SRP Module Upgrading a System That Contains Two SRP Modules Replacing an NVS Card Upgrading Memory on SRP Modules NVS Card Slot on SRP Module Displaying the Memory Installed Removing SODIMMs Adding New SODIMMs Sodimm Sockets on the SRP-5 and SRP-10 Module Verifying the Upgrade Replacing SFPs on I/O Modules Removing SFPs Possible Release Mechanisms on the SFP Installing SFPs Example of SFP Installing an SFP on a GE I/O Module Replacing Fan Trays Fan Tray in ERX-14xx Models Installing the Fan Tray Removing the Fan Tray Installing a Cable-Management Bracket on ERX-7xx Models 100 101 102 Troubleshooting Diagnosing Problems Understanding Status LEDs to Troubleshoot Troubleshooting Power FailuresCauses of Power Failures Symptom Possible Problems Actions LED Identification Redundant 106 107 SRP Module LEDs 109 Normal Activity of Functional Status Leds During Booting LED Activity Issue the reload slot slotnumber Status Process 112 Redundancy Status of a Line Module Monitoring Temperatures of ModulesRedundancy Status Detecting Double-Bit Errors Resetting Line Modules and SRP ModulesDouble-Bit Errors on SRP Modules Fixing Double-Bit Errors 116 Appendixes Appendixes ERX-14xx Models Specifications Category System SpecificationsERX-14xx Models Specifications Category Specification Space Requirements 121 ERX-7xx Models Specifications ERX-7xx Models Specifications Category 123 124 ERX-310 Router Specifications ERX-310 Router Specifications Category 126 127 128 Installation Guidelines Requirements Your Preinstallation Responsibilities Environmental Requirements Regulatory Compliances Installation Guidelines and Requirements Safety Guidelines ERX-310 Power Cord Warnings AC Model ERX-310 Router Warnings AC Model Equipment Rack Requirements ERX Routers Installed in a Rack Mechanical Requirements Proper Rack Installation Space Requirements Cabling Recommendations Airflow for ERX Routers Product Reclamation and Recycling Program Hardware Compliance Federal Communications Commission FCC Statement FCC Requirements for Consumer Products Industry Canada Notice CS-03 Avis CS-03 d’Industrie Canada C. Explanatory Notes Equipment Attachment Limitations EC Declaration of Conformity Cable Pinouts SRP I/O Module SRP I/O Module-RS-232 Serial Connector Pinout Signal SRP I/O Module Serial Port SRP I/O Module-RJ-45 Connector Pinout Signal SRP I/O Module Ethernet Port CT1 and CE1 I/O Modules Lists the pinout for the straight-through adapter CT1/CE1 I/O Module-RJ-48C Connector Pinout Signal CT1 I/O Module Ports CE1 I/O Module with Telco Connectors Pinout of 50-Pin Telco Connector to Ports Signal Pin Signal 149 150 Contacting Customer Support Return ProcedureContacting Customer Support and Returning Hardware Locating Component Serial Numbers 152 Information You Might Need to Supply to Jtac Representative Module Serial Number ID Label Packing Instructions for Returning a Chassis Returning Products for Repair or ReplacementTools and Parts Required 155 156 Declaration of Conformity Declaration of Conformity 158 Index Index Symbols Accessing Series routers Modules QoS, packet classification for 21/V.35 connectors, cabling