Message Appears when Action | JVC GV-DS2 manual

40

EN

L

IS

T

O

F

ER

R

O

R

ME

S

S

A

GES

Message

⬤ Appears when:

Page

⬛ Action:

COM port is not

⬤ Not connected to COM port set by JLIP Initialize.

20

available.

⬛ Check the COM port number and connector and

retry JLIP initialization.

Connected device

⬤ Connected devices are not turned on.

20, 21

not found.

⬤ Selected COM port is not connected properly.

⬛ Make sure connection is proper and carry out JLIP

initialization. Then turn on this unit and the

connected devices.

Error — Transfer

⬤ Video unit is brought to STOP or ends playback

halted.

during automatic capture.

⬛ Check the auto capture setting.

—

⬤ Full image data (768 x 552 pixels) cannot be

captured if you start auto capture at the beginning

of the tape. Video capture stops if video playback

is stopped.

⬛ Start video capture 20 seconds after the start of the

30

recording.

⬤ Tape is too short to match the preset number of

images or there is a section of non-recorded tape.

⬛ Click "OK", check the tape length and re-enter the

number of images to be captured. Use a fully

recorded tape.

Image 40

JVC GV-DS2 manual Message Appears when Action

Contents

GV-DS2 Dear Customer It is recommended that you Some DO’S and DON’TS on the Safe USE of Equipment Maintenance How to handle a CD-ROMDo not place the Video Capture Docking Station Contents EN Troubleshooting List of Error Messages Additional OperationsJlip Video Producer Software Starting Jlip Video Producer Software Troubleshooting Major Specifications Index Advanced Operations Internet homepage Business presentationsVideo journal and postcards Jlip Video Capture Software Video Capture FacilityJlip Control Facility Jlip Video Producer Software Controls and Conne Ctors Connect the power cord to an AC outlet Open CoverAttach FIX When connected with the camcorder When connected with the Video Printer Power Connec T Ions Jlip Video Capture Software Section What is video capture software ? What is Jlip ?EN Getting Started Operating Environment Installation Procedure Windows Preparation Main Desktop Window HOW to Close the Program Click Exit from File in the menu bar. The program closes Initializing Jlip Select Transfer Rate. Normally select Select Units Menu bar Main Desktop WindowControl buttons When an image display box is double-clicked Image display area Each pulldown menu is configured as follows Menu BAR VCR operation window Set-up Image data flow Capturing Video Images Set-up Capture Mode Step by Step Step by Step Capture Automatic Capture EN V Ideo CA PtureProgram Capture Transfer Interval Capture Select Interval Capture Saving Save the Full Image Data Picture Data Format Capture ModeSelecting a Picture Format Counter Value Change Counter ResetModify Capture Point window appears Delete Index Image and Full Image Additional Operation SChange ID Create NEW Folder Open Index Using Jlip Video Producer Software Data Open Jlip jlp File window is displayed HOW to Store Jlip Video Producer Software Data Save As Jlip jlp File window is displayed Problem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counter Message Appears when Action Error Execute afterPlaying back Not enough disk EN Memo Jlip Video Producer Software Section Recorder PlayerVideo printer Installing Jlip Video Producer Software EN Prepare Devices Access Video ProducerSelect Serial Port Select Devices Select Recorder Control-menu box Menu bar Title bar Memo Elapsed Time Setting in/out points EN Basic Oper AtionsOperating camcorder Playback on TV Monitor Select Scene Start Playback EN Basic OP E Ration S DubbingPrepare NEW Tape Start Editing Start Saving Enter File NameSave File Select Floppy Disk Drive Opening a saved file Correcting and cutting the programmed counter data Overwriting the file Designatecopied Scene to beStore Designated Scene in Memory Designate Scene to be Transferred Basic Operat Ions Selecting a P.AE/EffectSelecting a Fade/Wipe Effect Select P.AE/EFFECT AE/Effect buttons Sepia Store button Position button Strobe Speed button Title bar Power buttonButton Content button Position buttonMULTI-PIX button Strobe Speed button Printing Bring UP Video Printer WindowPlayback Store Scene Quitting the Video Printer window Quitting the Jlip Video Producer windowClick Close Preparation Auto CaptureTo Print Captured Video Data with Video Printer To print only the cut-in scene on the edited tape Select Set-up Function Set Auto Capture EN Advan CED Oper Ations Connecting other device during operationChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer Window Access Record Time Correction Dialog BOX EN Advanced Operat IonsEnter Value Determine Value Rewind Tape to Beginning Reset Counter Counter resetWhen Using the Video Capture Software That power is on Power on all devices System Communication errorClose Check devices - Confirm Memory full - 99 events MaximumEnter correct value Your selection is not valid EN M Ajor Speci Fications Index GV-DS2