Manuals / JVC / Photography / Camcorder

JVC GV-DS2 manual Player, Recorder, Video printer

Models: GV-DS2

1 72

Download 72 pages 9.38 Kb

Page 44

44EN

GETTINGSTARTED

What is JLIP ?

JLIP* stands for Joint Level Interface Protocol, a new communication protocol which allows AV units equipped with a JLIP terminal to be controlled by a personal computer.

* is a registered trademark of JVC.

Operating Environment

●Personal computer with Microsoft® Windows® 3.1 or Windows® 95

●CPU Intel DX4® or higher processor

●Minimum RAM requirement: more than 8 MB

●Available Hard Disk space of at least 4 MB (When JLIP Video Capture Software is also installed, the minimum Hard Disk space required is 8 MB in total.)

●Colour display capable of at least 640 x 480 pixels, 256 colours Recommended 1024 x 768, 16.77 Mil colours

●1 free serial transmission port, compatible with 9600 bps transmission rate, connectable to RS-232C with 9 pin serial connector.

Recommended compatible with UART 16550A

●Mouse (Windows® compatible)

●CD-ROM drive

Note : An optional 9 pin serial conversion adapter is required for computers using serial communication port other than standard 9 pin.

*Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

*Other product and company names included in this instruction manual are trademarks and/or registered trademarks of their respective holders.

Devices to connect to the VIDEO CAPTURE DOCKING STATION

●Player

Digital camcorder: GR-DVX, GR-DV1* and GR-DVM1*

*Attach a Docking Station equipped with a JLIP connector to the GR-DV1 or GR-DVM1.

●Recorder

Recording deck equipped with a JLIP connector Recording deck equipped with a remote pause jack

Recording deck equipped with neither a JLIP connector nor a remote pause jack

●Video printer

Video printer equipped with a JLIP connector: GV-PT2

The JLIP Video Producer Software can be used with the GV-CB1 or GV-DS1. (As of August, 1997)

Image 44

JVC GV-DS2 manual Player, Recorder, Video printer

Contents

GV-DS2 Dear Customer It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment Do not place the Video Capture Docking Station How to handle a CD-ROMMaintenance Contents EN Troubleshooting List of Error Messages Additional OperationsJlip Video Producer Software Starting Jlip Video Producer SoftwareTroubleshooting Major Specifications Index Advanced OperationsVideo journal and postcards Business presentationsInternet homepage Jlip Video Capture Software Video Capture FacilityJlip Control Facility Jlip Video Producer SoftwareControls and Conne Ctors Connect the power cord to an AC outlet Open CoverAttach FIXWhen connected with the camcorder When connected with the Video PrinterPower Connec T Ions Jlip Video Capture Software Section What is video capture software ? What is Jlip ?EN Getting Started Operating EnvironmentInstallation Procedure WindowsPreparation Main Desktop WindowHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Control buttons Main Desktop WindowMenu bar When an image display box is double-clicked Image display areaEach pulldown menu is configured as follows Menu BARVCR operation window Set-upImage data flow Capturing Video ImagesSet-up Capture Mode Step by Step Step by Step CaptureProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Interval Capture Select Interval CaptureSaving Save the Full Image DataSelecting a Picture Format Capture ModePicture Data Format Modify Capture Point window appears Counter ResetCounter Value Change Change ID Additional Operation SDelete Index Image and Full Image Create NEW Folder Open IndexUsing Jlip Video Producer Software Data Open Jlip jlp File window is displayedHOW to Store Jlip Video Producer Software Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskEN Memo Jlip Video Producer Software Section Video printer PlayerRecorder Installing Jlip Video Producer Software EN Select Serial Port Access Video ProducerPrepare Devices Select Devices Select RecorderControl-menu box Menu bar Title barMemo Elapsed TimeSetting in/out points EN Basic Oper AtionsOperating camcorder Playback on TV MonitorSelect Scene Start PlaybackEN Basic OP E Ration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file Correcting and cutting the programmed counter dataOverwriting the file Designatecopied Scene to beStore Designated Scene in Memory Designate Scene to be TransferredBasic Operat Ions Selecting a P.AE/EffectSelecting a Fade/Wipe Effect Select P.AE/EFFECTAE/Effect buttons SepiaButton Position button Strobe Speed button Title bar Power buttonStore button Content button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneClick Close Quitting the Jlip Video Producer windowQuitting the Video Printer window To Print Captured Video Data with Video Printer Auto CapturePreparation To print only the cut-in scene on the edited tape Select Set-up Function Set Auto CaptureChanging ID number Connecting other device during operationEN Advan CED Oper Ations Access Name Change Dialog BOX Access Device Selection Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer WindowAccess Record Time Correction Dialog BOX EN Advanced Operat IonsEnter Value Determine ValueWhen Using the Video Capture Software Counter resetRewind Tape to Beginning Reset Counter That power is on Power on all devices System Communication errorClose Check devices - ConfirmMemory full - 99 events MaximumEnter correct value Your selection is not validEN M Ajor Speci Fications Index GV-DS2