Remove the cassette and cover, Timer again | JVC HM-HDS1U specification

EN 87

RECORDING

		SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
	5.	Audio dubbing is not possible.		● The tape speed had been set to LP at		Set the tape speed to SP at the
				the original recording.		original recording.
				● HDD deck
				This is normal. Audio dubbing is not
				available for HDD deck.

	7.	When performing Tape Dubbing,		● This is normal.
		the beginning of the dubbing start
		point is not dubbed.

TIMER RECORDING

	SYMPTOM			POSSIBLE CAUSE			CORRECTIVE ACTION
1.	Timer recording won’t work.			● The clock and/or the timer have			Set the clock and/or timer correctly.
				been set incorrectly.
				● The timer is not engaged.			Press TIMER and check to make sure
							that ‰appears on the front display
							panel.
				● The recorder has not been set up			Re-perform the set-up procedures.
				properly.			Make sure you have compensated for
							Guide Channel and recorder or cable
							box channel number mismatches
							( pg. 56).

2.	Timer programming won’t work.			● Timer recording is in progress.			Timer programming can’t be performed
							when timer recording is in progress.
							Wait until it finishes.

3.	‰and ]on the front display			● The timer is engaged but there’s no			VHS deck
	panel won’t stop blinking.			cassette loaded.			Load a cassette with the Record
							Safety tab intact, or cover the hole
							using adhesive tape.

4.	The cassette is automatically			● VHS deck			Remove the cassette and cover the
	ejected, and ‰and ]on the			The loaded cassette has had its			hole with adhesive tape, or insert a
	front display panel won’t stop			Record Safety tab removed.			cassette with the Record Safety tab
	blinking.						intact.
							Remove the cassette and set the erase
							protection switch to “REC”.

5.	‰blinks for 10 seconds and the			● TIMER has been pressed when there			Check the programmed data and re-
	timer mode is disengaged.			are no programs in memory, or the			program as necessary, then press
				timer record program information			TIMER again.
				has not been programmed correctly.

6.	The cassette is automatically			● The end of tape was reached during			The program may not have been
	ejected, the power shuts off and ‰			timer recording.			recorded in its entirety. Next time
	and ]won’t stop blinking.						make sure you have enough time on
							the tape to record the entire program.

CONTINUED ON NEXT PAGE

Image 87

JVC HM-HDS1U manual Remove the cassette and cover, Protection switch to REC, Timer again

Contents

HM-HDS1U Do not place the recorder Dear Customer Installation USE Antenna Installation Instructions Servicing Before YOU Install Your NEW Recorder Before installing the recorder Before using the recorderWhile using the recorder Contents Situate Recorder Check ContentsPower Source Connections Auto blinks Channel numbers are displayed Plug & Play SetupPlug & Play Auto Clock Set/Auto Tuner Set Clock Access Main MenuAccess Initial SET Screen Access Clock SET Select Time Zone Select D.S.T. ModeSET Auto Clock to on Select Host Channel Manual SET TimeSET Date SET Year Set Receivable Channels Access Tuner SET ScreenTuner Turn on the Recorder ADD or Skip Desired Access Main Menu ScreenAccess Tuner SET Screen Access Manual Channel SET Screen Connect Cable BOX to Recorder Cable Box ControlSituate Controller Attach Controller Access Cable BOX SET Screen Turn on Cable BOXSelect Cable BOX Output Channel Enter Cable BOX Brand Access Cable BOX Brand SET Screen DBS receiver Fasten securely using the supplied adhesive stripsDBS Receiver Control Controller Set DBS Receiver Output Channel & DBS Receiver Brand Access DBS Receiver SET ScreenAt the Initial Set Up Turn on DBS Receiver SET DBS Receiver Brand Access DBS Receiver Setting Blue Back Access FunctionSelect Blue Back Mode Mode Setting Video Inputs ModeAccess Video Inputs Screen Select Video Inputs Simple Recording Stop Playback Simple PlaybackStart Playback Pause Playback Icons and their meanings Playback with HDD Navigation Access Scan Screen Select ProgramsScan for Beginnings of Programs About Live Memory Playback Setting Time for Live Memory PlaybackLive Memory Playback Start Live Memory Playback Pose by pressing Access Function ScreenSuperimpose Arrow to Superim To Recall Indication Playback Features Quick Rewind a little Change SpeedActivate Quick Skip Variable-Speed Search/ Reverse Motion Playback Start Rewind Repeat Playback Normal Playback OnlySelect The Soundtrack Viewing Recording FeaturesEngage TV Mode Select Channel for Point Load a CassetteSelect VHS Deck Find Program Start SET Tape Speed PAUSE/RESUMERecording Playback with VHS Navigation Access VHS SET UP Select VHS Navigation ModeSet VHS Navigation Tered Program Select ProgramScan for Beginning of Pro- gram with VHS Navigation Activate HIGH-SPEED Search Activate FRAME-BYChange SLOW-MOTION Speed Access Distant Code Start SearchIndex Search Press OSD Tuned-in channel or AUXiliary modeOperation mode Switchable to the tape remaining time display Tracking Tracking ModeAdjust Manual Engage Manual Beginning or E End shows you Where you are on the tape Counter ResetTape Position Indicator Press C.RESET Access VHS SET UP 1 Screen Select Picture Control ModePicture Control Access VHS SET UP Screen Select Video Stabilizer ModeVideo Stabilizer ∞, then press OK Select TBC ModeTBC by Pressing Arrow to %ﬁ Calibration by Calibration ModeAt the top of the HDD/VHS SET UP Active Video Calibration Recording Display Elapsed Recording Time Display Counter InformationDisplay Tape Remaining Time Exit the Display VHS Super VHS, S-VHS ET and VHS Super VHS ET Engage S-VHS ET Mode Engage RECORD-PAUSE Mode Locate Start PointResume Recording Stereo And SAP Second Audio Program To Record Stereo ProgramsTo Listen To Stereo Soundtrack During Recording VCR Plus+ Timer Programming Check Program Data VCR Plus+ Guide Channel Matching Changing VCR Plus+ SettingAccess Initial SET Initial SET UP by Input Receiving Channel Access Guide Channel SET Screen SET Program Stop Time Express Timer ProgrammingRecorded on SET Program Date SET Channel Number SET Weekly or DailySET Category CH+ Check Overlap ProgramReturn to the Normal STOP+/-,DATE+ Check, Cancel And Revise Programs VHS Deck onlyCH+ Auto SP→EP Timer Select Auto SP=EP Timer Mode To cancel REC Link mode, press REC Link again Timer RecordingPrepare the External Equipment for Timer Recording Engage REC Link Mode Duration Instant Timer Recording ITREngage ITR Mode SET Recording Limitations of Registration About Hybrid NavigationAbout Registration of Information About Editing of Programs Register NEW Index Access Modify ScreenModify Information Select Deck Modify Program Title Access Navigation ScreenEnter NEW Title Register NEW Title Press @%#ﬁ or 253∞ to move the arrow to Select NEW CategoryRegister NEW Category Modify Category For HDD Navigation Access Delete ScreenConfirm Deletion Delete Information Select Dubbing Option Access Easy DubbingDubbing Navigation Screen Start Dubbing Select REC Speed Normal Dubbing DubbingEND Dubbing Press VHS or S-VHS and select the program to be Press Pause on the remote control. To resumeRemote control Dard at the VHS SET UP 1 of the main Menu Program Editing Memory 1 program x 8 scenes Random Assemble Editing Start Editing Select the Other EDIT-IN and EDIT-OUT PointsPrepare VHS Deck for Recording Camcorder Edit From a For HDD deck Return to Normal ScreenStart Player Start Recorder Edit To Or From Another Make ConnectionsLoad Cassettes Start Recorder SET RECORDER’S Input ModeSelect Edit for PIC Start Player VHS Audio Dubbing SET Input ModeAudio Dubbing Engage Audio Dubbing END Audio Dubbing When monitoring the sound during Audio Dubbing, SET TV Brand Code SET Remote ControlTV Multi-Brand Remote Control Turn on the TV Cable Box Multi-Brand Remote Control Operate Cable BOXHDD or VHS or S-VHS Enter DBS Receiver Brand DBS Receiver Multi-Brand Remote ControlTurn on the DBS Receiver Ex. When pressing SET Remote Control CodeEnter Remote Control Code Confirm the Setting Recording won’t start Cassette gets stuck partwayPlayback won’t start HDD deck Protection switch to REC Timer againRemove the cassette and cover Re-perform the VCR Plus+ setup Procedure pgPlus+ system doesn’t work properly Can the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?What happens if the tape runs out during recording? #1 and ¡ Buttons pg $S-VHS ET Button pg # $ REAR1VIEW 12ANTENNA in Connector pg Display Panel Control 8Space Button pg Cancel Button pg List Of Terms NTSC-type colour signal and EIA Monochrome signal, 525 lines20C to 60C -4F to 140F EN for Servicing Only in U.S.A Warranty Only in U.S.A EN Memo Memo HM-HDS1U