To set the DIGITAL 2/3/4 terminals:
1. Press SETTING until DIGITAL 2/3/4 SETTING terminals setting appears on the 
display.
The display changes to show the current settings for the DIGITAL 2/3/4 terminals.
DIGITAL 2 terminal setting
DIGITAL 3 terminal setting DIGITAL 4 terminal setting
2. Press CONTROL UP 5/DOWN ° CONTROL
to select the appropriate digital | DOWN | UP |
|
| |
terminal settings. |
|
|
• Each time you press the buttons, the display changes to show the following:
When the DGTL COAX (DIGITAL 1) is set to “DVD”
2:CD 3: TV (or DBS*) 4: CDR Ò2: CD 3: TV (or DBS*) 4:MD** Ò
2:CD 3: MD** 4: CDR Ò 2: MD** 3: TV (or DBS*) 4: CDR Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “MD” **
2:CD 3: TV (or DBS*) 4: CDR Ò2: CD 3: TV (or DBS*) 4: DVD Ò
2:CD 3: DVD 4: CDR Ò2: DVD 3: TV (or DBS*) 4: CDR Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CDR”
2:CD 3: TV (or DBS*) 4: DVD Ò2: CD 3: TV (or DBS*) 4: MD** Ò
2:CD 3: MD** 4: DVD Ò2: MD** 3: TV (or DBS*) 4: DVD Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “TV” or “DBS”
2:CD 3: DVD 4: CDR Ò2: CD 3: DVD 4: MD** Ò
2:CD 3: MD** 4: CDR Ò2: MD** 3: DVD 4: CDR Ò (back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CD”
2:DVD 3: TV (or DBS*) 4: CDR Ò2: DVD 3: TV (or DBS*) 4: MD** Ò
2:DVD 3: MD** 4: CDR Ò2: MD** 3: TV (or DBS*) 4: CDR Ò (back to the beginning)
*If you have changed the source name from “TV” to “DBS,” “DBS” appears (see page 33).
**Change the source name to “MD” for TAPE/MD jacks when you use an MD recorder (see page 33).
Note:
When shipped from the factory, the DIGITAL IN terminals can be used as the digital input for the following components:
•DIGITAL 1 (coaxial): For DVD player
•DIGITAL 2 (optical): For CD player
•DIGITAL 3 (optical): For digital TV broadcast tuner
•DIGITAL 4 (optical): For CD recorder
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using the digital terminals (see page 10), you need to change the input mode for these components to the appropriate digital input mode correctly
— DGTL AUTO, DGTL DTS, or DGTL D.D.
Before you start, remember...
•The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.
•The digital input can be used for the main room sources. The analog input is always selected as the
On the front panel:
1.Press one of the source selecting button (DVD, TV SOUND/DBS, CD, CDR, or TAPE/MD)* for
which you want to change the input mode.
The lamp on the front panel button for selected source lights up.
DVD MULTI | DVD | VCR 1 | VCR 2 | VIDEO | TV SOUND/DBS |
PHONO | CD | CDR | TAPE / MD | USB AUDIO | FM / AM |
SOURCE NAME
Note:
*You can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting” on page 30.)
INPUT
2. Press INPUT ANALOG/DIGITAL ANALOG/DIGITAL briefly to change the input mode.
• Each time you press the button, the input | INPUT ATT |
| |
mode changes as follows: |
|
DGTL AUTO 
ANALOG
(Digital)
DGTL AUTO: Select this for the digital input mode. The receiver automatically detects the incoming signal.
always lights up on the display, and the digital signal indicator for the detected signals also lights up.
ANALOG: Select this for the analog input mode.
ANALOG always lights up.
When selecting “DGTL AUTO”, following indicators showing detected signals light up on the display.
LINEAR PCM : Lights up when Linear PCM signals come in.
• Flashes while seaching the incoming signals.
LINEAR PCM : Lights up when the digital signals are not recognized.
DIGITAL : Lights up when Dolby Digital signals come in. 
: Lights up when DTS Digital Surround signals
come in.
31
