From the remote control:
1. Press DSP MODE repeatedly until | DSP |
MODE | |
“5CH STEREO*” appears on the |
|
display. |
|
The DSP MODE lamp on the front panel button lights up, and the DSP indicator also lights up on the display.
*“4CH STEREO” appears on the display when you have set “CTR SPK” to “NONE.” (See page 29.)
Adjusting the 3D-PHONIC Modes
Once you have adjusted the
IMPORTANT:
Check to see if the proper indicator(s) and information appear on the display on the front panel before/while using the buttons and controls.
2. Press SOUND.
SOUND
For the main room operations:
The 10 keys are activated for sound adjustments.
3.Select the speaker you want to adjust.
•To select the center speaker level, press CENTER (for 5CH STEREO only).
•To select the left rear speaker level, press REAR•L.
•To select the right rear speaker level, press REAR•R.
CENTER | REAR·L | REAR·R |
4 | 7/P | 8 |
4. Press LEVEL + or LEVEL – to | LEVEL+ | |
adjust the speaker output levels ( | ||
| ||
LEVEL– |
•Each time you press the button, the indication corresponding to the button
selected in step 3 appears on the display window on the remote control.
5.Repeat steps 3 and 4 to adjust the other speaker output levels.
6. Press CENTER TONE to select the | CENTER TONE |
center tone level you want (for 5CH +10 | |
STEREO only). | 100+ |
|
•The center tone adjustment affects the
•Each time you press the button, the display changes to show the following:
CTR TONE 1 CTR TONE 2 CTR TONE 3
(Softer)(Soft)(Flat)
CTR TONE 5 |
| CTR TONE 4 |
| ||
(Sharper) |
| (Sharp) |
To make the dialogue softer, select “CTR TONE 1” or “CTR
TONE 2.”
To make the dialogue clearer, select “CTR TONE 4” or “CTR TONE 5.”
When “CTR TONE 3” is selected, no adjustment is applied.
•The MAIN ROOM indicator is lit.
•The source name for the
•When using the remote control:
– Set MAIN ROOM/SUB ROOM selector to
“MAIN ROOM.”
– Check to see if the following information
appear on the display window on the remote |
|
|
|
|
|
MAIN ROOM SUB ROOM | |||||
control. |
|
|
|
|
|
Buttons | Indications |
|
|
SOUND | SOUND |
|
|
After pressing SOUND, the following function are assigned to the specific number buttons:
Buttons | Indications | |
|
| |
EFFECT | SOUND | |
CENTER TONE | ||
| ||
CENTER | CTR | |
REAR•L | REARL | |
REAR•R | REARR | |
|
|
|
| STANDBY | ON |
| MAIN ROOM SUB ROOM |
| |
Ex. “SOUND” appears on the display | MAIN ROOM | SUB ROOM TV/CATV/DBS | VCR1 |
ON/OFF | ON/OFF POWER | POWER |
window.
MAIN ROOM SUB ROOM
When you press the buttons listed above, the indication appears for 5 – 10 seconds for your confirmation.
Before you start, remember...
•Make sure that you have set the speaker information correctly (see page 29).
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.
•You cannot adjust the center speaker output level when you have set “CTR SPK” to “NONE” See page 29.
•To adjust the front speaker output balance and subwoofer output level, see pages 27 and 28.
47