JVC RX-9010VBK manual Dance CLUB, or Pavilion appears on the display

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 29).

•When the SUB ROOM and SPEAKERS SUB ROOM indicators are lit on the display, you can only use 3D-PHONIC modes for the main room source.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

•You cannot adjust the center speaker output level when you have set “CTR SPK” to “NONE” (see page 29).

•You cannot adjust the rear speaker output level when you have set “REAR SPK” to “NONE” (see page 29).

•To adjust the front speaker output balance and subwoofer output level, see pages 27 and 28.

On the front panel:

1.Press DSP MODE repeatedly until DSP MODE the DAP mode you want to adjust

— THEATER 1, THEATER 2, HALL 1, HALL 2, LIVE CLUB,

DANCE CLUB, or PAVILION — appears on the display.

The DSP MODE lamp on the front panel button lights up, and the DSP indicator also lights up on the display.

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

4.Adjust the overall levels of the effect. EFFECT

1)Press EFFECT repeatedly until “EFFECT” appears on the display. The display changes to show the current setting.

2) Press CONTROL UP 5/DOWN °	CONTROL
	DOWN UP
to select the effect level you want.

• Each time you press the button, the display changes to show the following:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5 EFFECT 4

As the number increases, the selected DAP effect becomes stronger. (Normally set it to “EFFECT 3.”)

5. Adjust the room size (sense of spaciousness).

•When you have set “REAR SPK” to “NONE,” the 3D- PHONIC indicator also lights up.

2. Adjust the speaker output levels.	LEVEL
1) Press LEVEL ADJUST repeatedly until	ADJUST
one of the following indications appears on
the display.
“CENTER”:
To adjust the center speaker level.
“REAR L”:
To adjust the left rear speaker level.

1)Press EFFECT repeatedly until “ROOM SIZE” appears on the display.

The display changes to show the current setting.

2)Press CONTROL UP 5/DOWN °to select the room size you want.

•Each time you press the button, the display changes to show the following:

EFFECT

CONTROL

DOWN UP

“REAR R”:

To adjust the right rear speaker level.

CONTROL

2) Press CONTROL UP 5/DOWN °to DOWN UP adjust the selected speaker output

level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

ROOMSIZE 1ROOMSIZE 2ROOMSIZE 3

ROOMSIZE 5 ROOMSIZE 4

As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally set it to “ROOMSIZE 3.”)

6. Adjust the liveness.

EFFECT

3.Adjust the center tone.

1)Press EFFECT repeatedly until “CTR TONE” appears on the display.

The display changes to show the current setting.

2)Press CONTROL UP 5/DOWN ° to select the center tone level you want.

EFFECT

CONTROL

DOWN UP

1)	Press EFFECT repeatedly until
	“LIVENESS” appears on the display.
	The display changes to show the current
	setting.
2)	Press CONTROL UP 5/DOWN °to
	select the liveness level you want.
	• Each time you press the button, the
	display changes to show the following:

CONTROL

DOWN UP

The center tone adjustment affects the mid-frequency range, which the human voice is mostly made up of.

•Each time you press the button, the display changes to show the following:

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5	CTR TONE 4
(Sharper)	(Sharp)

LIVENESS 1 LIVENESS 2 LIVENESS 3

LIVENESS 5 LIVENESS 4

As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.” (Normally set it to “LIVENESS 3.”)

42