CONTROL
DOWN UP

When playing a software encoded with the Dolby Digital or

DTS Digital Surround, the following symptoms may occur:

Sound does not come out at the beginning of playback.

Noise comes out while using the searching for or skipping chapters or tracks.

In this case press CONTROL UP 5/DOWN ° to select “DGTL D.D” or “DGTL DTS”

while “DGTL AUTO” still remains on the

display.

• Each time you press the button, the input mode changes as follows:

DGTL AUTO

 

DGTL D.D

 

 

 

(Digital)

(Digital Dolby Digital)

DGTL DTS

(Digital)

“DGTL” lights instead of “DGTL AUTO” on the display when “DGTL D.D” or “DGTL DTS” is selected.

When selecting “DGTL D.D” or “DGTL DTS”, following indicators showing detected signals light up on the display.

: Always lights up when “DGTL D.D” or “DGTL DTS” is selected.

When selecting “DGTL D.D”

DIGITAL

: • Lights up when Dolby Digital signals come in.

Flashes when Dolby Digital signals are not recognized.

When selecting “DGTL DTS”

: • Lights up when DTS Digital Surround signals come in.

Flashes when DTS Digital Surround signals are not recognized.

Note:

When you turn off the power or select another source, “DGTL DTS” and “DGTL D.D” settings are canceled and the digital input mode is automatically reset to “DGTL AUTO.”

To change the input mode back to analog input, select

“ANALOG” in step 2.

From the remote control:

1.Press the source selecting button (DVD, CD, TAPE/MD, CDR or TV/DBS)* for which you want to change the input mode.

DVD

DVDMULTI

PHONO

CD

VCR 1

VCR 2

TAPE/MD

CDR

TV/DBS

VIDEO

FM/AM

USB AUDIO

Note:

*You can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting” on page 30.)

2. Press ANALOG/DIGITAL INPUT to ANALOG/DIGITAL

change the input mode.

INPUT

 

Each time you press the button, the input mode changes as follows:

DGTL AUTO ANALOG

(Digital)

When playing a software encoded with the Dolby Digital or

DTS Digital Surround, “DGTL AUTO” may not happen to work well. In this case press CONTROL UP 5/DOWN °on the front panel to select “DGTL D.D” or “DGTL DTS” (while “DGTL AUTO” remains on the display).

Note:

You can select “DGTL D.D” or “DGTL DTS” with “On-screen Menus”

by using the remote control (see page 50).

Selecting the Video Input Terminal

This receiver is equipped with component video input terminals for the DVD player and DBS tuner, which give you higher picture quality. When you use the component video input terminals for the DVD player and/or DBS tuner, change the video input terminal setting.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press SETTING repeatedly until

SETTING

“VIDEO DVD” or “VIDEO DBS”

 

 

appears on the display.

 

The display changes to show the current setting.

Select “VIDEO DVD” to select the video input terminal for the DVD player and “VIDEO DBS” for the DBS tuner.

2. Press CONTROL UP 5/DOWN °

CONTROL

DOWN UP

to select the appropriate video

 

input terminal.

 

Each time you press the button, the display changes to show the following:

COMPNT S/C

(Component) (S-video/Composite)

COMPNT: Select this when you connect the DVD player or DBS tuner to the component video input terminals.

S/C: Select this when you connect the DVD player or DBS tuner to the composite video or S-video input terminal.

Note:

Without changing the video input terminal setting, you can see the picture through the video input terminals, but cannot use the AV COMPU LINK remote control system correctly (see page 62).

32

Page 35
Image 35
JVC RX-9010VBK manual Selecting the Video Input Terminal, Video DVD or Video DBS Appears on the display