8.Adjust the liveness.
1)Press EFFECT repeatedly until “LIVENESS” appears on the display. The display changes to show the current setting.
2)Press CONTROL UP 5/DOWN °to select the liveness level you want.
•Each time you press the button, the display changes to show the following:
EFFECT
CONTROL
DOWN UP
Before you start, remember...
•Make sure that you have set the speaker information correctly (see page 29).
•This function does not work when you activate the
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.
•You cannot adjust the center speaker output level and select the center tone level for 4 CH Stereo mode.
•To adjust the front speaker output balance and subwoofer output level, see pages 27 and 28.
LIVENESS 1 LIVENESS 2 LIVENESS 3
LIVENESS 5 | LIVENESS 4 |
As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.” (Normally set it to “LIVENESS 3.”)
On the front panel:
1. Press DSP MODE repeatedly until | DSP MODE |
| |
“5CH STEREO*” appears on the |
|
display. |
|
The DSP MODE lamp on the front panel button lights up, and the DSP indicator also lights up on the display.
*“4CH STEREO” appears on the display when you have set “CTR SPK” to “NONE.” (See page 29.)
Adjusting the 5 CH/4 CH Stereo Mode
IMPORTANT:
Check to see if the proper indicator(s) and information appear on the display on the front panel before/while using the buttons and controls.
For the main room operations:
•The MAIN ROOM indicator is lit.
•The source name for the
•When using the remote control:
–Set MAIN ROOM/SUB ROOM selector to
“MAIN ROOM.”
– Check to see if the following information |
|
|
|
|
|
MAIN ROOM SUB ROOM | |||||
appear on the display window on the remote |
|
|
|
|
|
control. |
|
|
|
|
|
2.Adjust the speaker output levels.
1)Press LEVEL ADJUST repeatedly until one of the following indications appears on the display.
“CENTER”: (for 5CH STEREO only) To adjust the center speaker level.
“REAR L”:
To adjust the left rear speaker level. “REAR R”:
To adjust the right rear speaker level.
2)Press CONTROL UP 5/DOWN ° to adjust the selected speaker output level (from
3)Repeat 1) and 2) to adjust the other speaker output levels.
LEVEL
ADJUST
CONTROL
DOWN UP
3. Adjust the center tone (for 5CH STEREO only.)
| Buttons | Indications | ||
| SOUND | SOUND |
| |
|
|
|
|
|
After pressing SOUND, the following function are | ||||
assigned to the specific number buttons: | ||||
|
|
|
| |
| Buttons | Indications |
| |
|
|
|
| |
| CENTER TONE | SOUND |
|
|
| CENTER | CTR |
|
|
| REAR•L | REARL |
|
|
| REAR•R | REARR |
|
|
|
|
|
|
|
1)Press EFFECT repeatedly until “CTR TONE” appears on the display.
The display changes to show the current setting.
2)Press CONTROL UP 5/DOWN ° to select the center tone level you want.
•The center tone adjustment affects the
•Each time you press the button, the display changes to show the following:
EFFECT
CONTROL
DOWN UP
Ex. “SOUND” appears on the display |
| STANDBY | ON |
MAIN ROOM SUB ROOM |
| ||
MAIN ROOM | SUB ROOM TV/CATV/DBS | VCR1 | |
window. | ON/OFF | ON/OFF POWER | POWER |
|
|
|
MAIN ROOM SUB ROOM
When you press the buttons listed above, the indication appears for 5 – 10 seconds for your confirmation.
CTR TONE 1 CTR TONE 2 CTR TONE 3
(Softer)(Soft)(Flat)
CTR TONE 5 |
| CTR TONE 4 |
| ||
(Sharper) |
| (Sharp) |
To make the dialogue softer, select “CTR TONE 1” or
“CTR TONE 2.”
To make the dialogue clearer, select “CTR TONE 4” or
“CTR TONE 5.”
When “CTR TONE 3” is selected, no adjustment is applied.
Continued to the next page.
46