JVC RX-9010VBK manual Adjusting the Surround Modes

Adjusting the Surround Modes

Once you have adjusted the Surround modes, the adjustment is memorized for each source. You can also use a Surround mode with a DAP mode (see page 43).

IMPORTANT:

Check to see if the proper indicator(s) and information appear on the display on the front panel before/while using the buttons and controls.

For the main room operations:

•The MAIN ROOM indicator is lit.

•The source name for the sub-room is not lit on the display.

•When using the remote control:

– Set MAIN ROOM/SUB ROOM selector to

“MAIN ROOM.”

– Check to see if the following information
					MAIN ROOM		SUB ROOM
appear on the display window on the remote
control.
	Buttons	Indications
	SOUND	SOUND
	After pressing SOUND, the following function are
	assigned to the specific number buttons:
	Buttons	Indications
	CENTER TONE	SOUND
	CENTER		CTR
	REAR•L	REARL
	REAR•R	REARR
						STANDBY	ON
			MAIN ROOM SUB ROOM
Ex. “SOUND” appears on the display			MAIN ROOM	SUB ROOM TV/CATV/DBS			VCR1
			ON/OFF		ON/OFF POWER		POWER
window.			MAIN ROOM SUB ROOM

When you press the buttons listed above, the indication appears

for 5 – 10 seconds for your confirmation.

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 29).

•When the SUB ROOM and SPEAKERS SUB ROOM indicators are lit on the display, the SURROUND ON/OFF button does not work.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 3 again.

•You cannot adjust the center speaker output level and center tone when you have set “CTR SPK” to “NONE.” See page 29.

•You cannot adjust the rear speaker output levels when you have set “REAR SPK” to “NONE.” See page 29.

•To adjust the front speaker output balance and subwoofer output level, see pages 27 and 28.

From the remote control:

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with DOLBY SURROUND mark.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with mark.

D I G I T A L

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to	SURROUND
activate an appropriate Surround	ON/OFF
mode — PRO LOGIC, DOLBY
DIGITAL or DTS SURROUND.

The SURROUND ON/OFF lamp on the front panel button lights up.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

3. Press TEST to check the speaker						TEST
output balance.
“TEST TONE L” starts flashing on the display,
and a test tone comes out of the speakers in the
following order:
	TEST TONE L		TEST TONE C		TEST TONE R
	(Left front speaker)		(Center speaker)		(Right front speaker)
		TEST TONE LS		TEST TONE RS
		(Left rear speaker)		(Right rear speaker)

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CTR SPK” is set to “NONE” (see page 29).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 29).

•If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.

SOUND

4. Press SOUND.

The 10 keys are activated for sound adjustments.

5.Select the speaker you want to adjust.

•To select the center speaker level, press CENTER.

•To select the left rear speaker level, press REAR•L.

•To select the right rear speaker level, press REAR•R.

CENTER	REAR·L	REAR·R
4	7/P	8

6. Press LEVEL + or LEVEL – to	LEVEL+
adjust the speaker output levels (–	LEVEL–
10 dB to +10 dB).

• Each time you press the button, the

indication corresponding to the button selected in step 5 appears on the display window on the remote control.

7.Repeat steps 5 and 6 to adjust the other speaker output levels.

TEST

8. Press TEST again to stop the test tone.

Continued to the next page.

40