Overview Menu, Engine Metering Menu | Kohler 48VDC, 6VSG, 24VDC

3.9 Overview Menu

Overview ---->		Active Alert
1.2 h		(if any)
		Genset Status
		Standby
		Generator:		54V
		% Load		73%
		Engine:		125F
		Oil Pressure: OK
		Battery:		13.3V
				13.3V
		Engine Runtime:
			100.6 h
		Date:	02DEC2011
		Time:	HR:MNpm
		Next Exercise:
		09:00p 09Dec2011
		Next Maintenance:
		150 h or Mar2012
		SW Version:
		4.06
		<----	Return
Figure 3-10	Overview Menu
TP-6843 1/13

3.10 Engine Metering Menu

The engine metering menu displays engine status information as shown in Figure 3-11.This menu displays status information only. No settings can be changed from this menu.

Engine	---->	Eng Speed:
Metering		2300 R/min
		Oil Pressure:
		Switch: OK
		Oil Temperature:
		125 F
		Battery:
		13.3 V
		<---- Return
		tp6810

Figure 3-11Engine Metering Menu

Section 3 VSC Controller Operation 31

Image 31

Kohler 48VDC, 6VSG, 24VDC, 36VDC manual Overview Menu, Engine Metering Menu

Contents

TP-6843 1/13a VSC Engine Identification Product Identification InformationController Identification Generator Set Identification Numbers Table of Contents Scheduled Maintenance Table of ContentsAppendix a Abbreviations Battery Safety Precautions and InstructionsAccidental Starting Exhaust System Engine Backfire/Flash Fire Fuel System Hazardous Noise Use extreme care when handling, storing, and using fuels Hot Parts Heavy Equipment List of Related Literature Introduction Emission Information Nameplate Service Assistance Service Assistance TP-6843 1/13 Alternator Descriptions and Service ViewsIntroduction Engine Generator Set Enclosure Programmable Interface Module PIM AccessoriesCarburetor Heater OnCue Generator Management System Service Views 3Optional Communications Kit Components Generator Set Operation Prestart ChecklistTheory of Operation Generator Set Operation Exercising the Generator Set Exercise FaultsShutdowns Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown 5Controller Fault Messages Generator Set Operation TP-6843 1/13 VSC Controller Operation Control and IndicatorsVSC Generator Set Controller Controller Keypad LED Indicators LCD Display 6Autopaging Displays, Automatic Mode Procedure to Change Settings Controller PowerBattery Charging Changing Settings 7Changing Settings Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings 8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller Menus Engine Metering Menu Overview Menu Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Genset System Menu System Parameters for Battery Bank Charging Nominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the Exerciser Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Password Networking Configuration Submenu OnCue Password Rbus Rbus Information 25Remote Devices Submenu Remote Devices Submenu Programmable Interface Module PIM Status Menu Event Log Procedure to View Event History VSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled Maintenance Fuel Service Schedule, 6VSG Models Oil Check Oil Change ProcedureLubrication System Low Oil Pressure Shutdown Spark Plugs Resetting the Maintenance Timer Precleaner Service Air Cleaner ServicePaper Element Service Cooling System Engine Starting Battery Cylinder Lubrication Storage ProcedureLubricating System Fuel System Battery Introduction TroubleshootingFault Messages Controller Service Access Problem Possible Cause Recommended Action Troubleshooting Abdc Appendix a Abbreviations Systeme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved