25Remote Devices Submenu | Kohler 24VDC, 6VSG, 36VDC, 48VDC instruction

3.16.4 Remote Devices Submenu

Check the status of remote devices communicating through RBUS (see Figure 3-25). Device types can include:

Programmable Interface Module (PIM)

The serial numbers for the PIM are printed on the circuit boards inside the enclosures.

From Figure 3-24:

Remote ---->

Devices

S/N: XXXXXXXXX

<<*DeviceType*>>

Module Status:

Connected

Comm. Errors: 12345

Comm. Timeouts: 12345

Module ID: 12

Firmware Ver.: 122

(Dis)Connected: MM/DD/YY 12:12 PM

Return ---->

S/N: XXXXXXXXX	<---- Return
<<DeviceType>>

Connected: Displays the date and time that the device was connected.

Disconnected: Displays the last date and time of successful communication.

tp6804

Figure 3-25Remote Devices Submenu

TP-6843 1/13

Section 3 VSC Controller Operation 41

Image 41

Kohler 24VDC, 6VSG, 36VDC, 48VDC manual 25Remote Devices Submenu

Contents

TP-6843 1/13a VSC Controller Identification Product Identification InformationGenerator Set Identification Numbers Engine Identification Table of Contents Appendix a Abbreviations Table of ContentsScheduled Maintenance Accidental Starting Safety Precautions and InstructionsBattery Exhaust System Engine Backfire/Flash Fire Fuel System Hazardous Noise Use extreme care when handling, storing, and using fuels Hot Parts Heavy Equipment List of Related Literature Introduction Emission Information Nameplate Service Assistance Service Assistance TP-6843 1/13 Introduction Engine Descriptions and Service ViewsGenerator Set Enclosure Alternator Carburetor Heater AccessoriesOnCue Generator Management System Programmable Interface Module PIM Service Views 3Optional Communications Kit Components Theory of Operation Prestart ChecklistGenerator Set Operation Generator Set Operation Exercising the Generator Set Shutdowns FaultsExercise Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown 5Controller Fault Messages Generator Set Operation TP-6843 1/13 VSC Generator Set Controller Control and IndicatorsVSC Controller Operation Controller Keypad LED Indicators LCD Display 6Autopaging Displays, Automatic Mode Battery Charging Controller PowerChanging Settings Procedure to Change Settings 7Changing Settings Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser 8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller Menus Engine Metering Menu Overview Menu Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Genset System Menu System Parameters for Battery Bank Charging Nominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the Exerciser Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Password Networking Configuration Submenu OnCue Password Rbus Rbus Information 25Remote Devices Submenu Remote Devices Submenu Programmable Interface Module PIM Status Menu Event Log Procedure to View Event History VSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled Maintenance Fuel Service Schedule, 6VSG Models Lubrication System Oil Change ProcedureLow Oil Pressure Shutdown Oil Check Spark Plugs Resetting the Maintenance Timer Paper Element Service Air Cleaner ServicePrecleaner Service Cooling System Engine Starting Battery Lubricating System Storage ProcedureFuel System Cylinder Lubrication Battery Fault Messages TroubleshootingController Service Access Introduction Problem Possible Cause Recommended Action Troubleshooting Abdc Appendix a Abbreviations Systeme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved