112
Effects
EQ and Filters (EQ/Filter)

b: Emphasis Freq

This parameter sets the frequency to be emphasized. Higher val-

ues will emphasize lower frequencies.

c: Enhancer Delay L [msec]

d: Enhancer Delay R [msec]

These parameters set the delay time for the Enhancer left and

right channel. Specifying a slightly different delay time for the

left and right channel will add a stereo image, de pth, and width

to the sound.

10: Stereo Isolator

This is a stereo effect that separates the input signal into low,

mid, and high-frequency bands, and controls the volume of each

band independently. For example you can separately boost or cut

the kick, snare, and hi-hat sounds from a drum signal in real-

time.

11: St. Wah/Auto Wah(Stereo Wah/Auto Wah)

This stereo wah effect allows you to create sounds from vintage

wah pedal simulation to auto-wah simulation, and much

broader range settings.

a Trim 0...100 Sets the input level
b Low/Mid [Hz] 100...500 Sets the frequency at which the low
and mid bands are divided
c Mid/High [Hz] 2000...6000 Sets the frequency at which the mid
and high bands are divided
d
Low Gain [dB] –Inf,
–59...+12 Sets the low-frequency gain
Src Off...Tempo Selects the source that will
modulate low-frequency gain
Amt –72...+72 Sets the amount by which the low-
frequency gain will be modulated
e
Mid Gain [dB] –Inf,
–59...+12 Sets the mid-frequency gain
Src Off...Tempo Selects the modulation source for
mid-frequency gain
Amt –72...+72 Sets the amount by which the mid-
frequency gain will be modulated
f
High Gain [dB] –Inf,
–59...+12 Sets the high-frequency gain
Src Off...Tempo Selects the modulation source for
high-frequency gain
Amt –72...+72 Sets the amount by which the high-
frequency gain will be modulated
g
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
D
-mod
D
-mod
D
-mod
Left
Right
FX Amt
FX Amt
Stereo In - Stereo Out
Trim
Isolator
Low
Mid
High
Trim
Low
Mid
High
a
Frequency
Bottom 0...100 Sets the lower limit of the wah
center frequency
Frequency Top 0...100 Sets the upper limit of the wah
center frequency
b
Sweep Mode
Auto,
D-mod,
LFO
Selects the control from auto-wah,
modulation source, and LFO
Src Off...Tempo Selects the modulation source for
the wah when Sweep Mode=D-mod
Respon 0...100 Sets the response speed when
Sweep Mode = Auto or D-mod
c
Envelope Sens 0...100 Sets the sensitivity of auto-wah
Envelope
Shape –100...+100 Sets the sweep curve of auto-wah
d
LFO Frequency
[Hz] 0.02...20.00 Sets the speed of the LFO
Src Off...Tempo Selects a modulation source for LFO
speed
Amt –20.00...
+20.00
Sets the modulation amount of LFO
speed
e
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w Selects the type of notes that
specify the LFO speed
Times x1...x32 Sets the number of notes that
specify the LFO speed
f
Resonance 0...100 Sets the resonance amount
Low Pass Filter Off, On Switches the wah low pass filter on
and off
g
Output Level 0...100 Sets the output level of the effect
sound
Src Off...Tempo Selects the modulation source that
will control the effect output level
Amt –100...+100 Sets the modulation amount of the
effect output level
h
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
Stereo In - Stereo Out
D
-mod
Envelope Sens
Envelope Shape
Response
FX Amt
Wah
Sweep Mode
D-mod
Auto
Left
Right FX Amt
LFO
LFO
Wah
+