121
Effects
Overdrive, Amp models, and Mic models (OD Amp Mic)
Advanced
25: Bass Amp+Cabinet(Bass Amp Model+Cabinet)

This simulates a bass amp and speaker cabinet.

a: Amp Type

h: Cabinet Type

Recommended Combinations of Bass Amp Models and Cabi-

nets:

26: Tube PreAmp Model(Tube PreAmp Modeling)

This effect simulates a two-stage vacuum tube preamp. You can

make individual settings for two vacuum tubes connected in

series. This lets you create the warm sound typical of vacuum

tubes.

aAmp Type
LA STUDIO,
JAZZ ,
GOLD PANEL
,
SCOOPED,
VALVE2, VA LVE,
CLASSIC
Selects the type of the amplifier
b
Volume 0...100 Sets the output level
Src Off...Tempo Selects the modulation source for
the output level
Amt –100...+100 Sets the modulation amount of the
output level
c Bass 0...100 Sets the bass (low range) level
dMiddle 0...100 Sets the middle (mid range) level
Mid Range 0...4 Sets the mid-frequency range
e Treble 0...100 Sets the treble (high range) level
f Presence 0...100 Sets the presence (high-frequency
tone)
gCabinet
Simulater Off, On Switches the cabinet simulator on/
off
hCabinet Type
LA - 4x10,
MODERN -
4x10,
METAL - 4x10,
CLASSIC -
8x10,
UK - 4x12,
STUDIO - 1x15,
JAZZ - 1x15,
VOX AC100 -
2x15,
US - 2x15,
UK - 4x15,
LA - 1x18,
COMBI - 1x12
& 1x18
Selects the cabinet type
i
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
Amp Type Cabinet Type
LA STUDIO LA - 4x10, LA - 1x18
JAZZ JAZZ - 1x15
GOLD PANEL MODERN - 4x10
SCOOPED METAL - 4x10
VALVE2 CLASSIC - 8x10
VALVE CLASSIC - 8x10
CLASSIC COMBI - 1x12 & 1x18
+
Left
Right
FX Amt
Volume
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
D
-mod
Bass Amp Model1 Cabinet Simulator
a
Tube1 Low Cut
[Hz] Thru, 21...8.00k Sets the cutoff frequency for the low
cut filter of stage 1
High Cut [Hz] 53...20.00k,
Thru
Sets the cutoff frequency for the
high cut filter of stage 1
b
Tube1 Gain
[dB] –24.0...+24.0 Sets the input gain for stage 1
Saturation [%] 0...100 Sets the input/output response for
stage 1
c Tube1 Bias 0...100 S ets the bias voltage for stage 1
dTube1 Phase Normal,
Wet Invert Turns phase reversal on/off
e
Tube2 Low Cut
[Hz] Thru, 21...8.00k Sets the cutoff frequency for the low
cut filter of stage 2
High Cut [Hz] 53...20.00k,
Thru
Sets the cutoff frequency for the
high cut filter of stage 2
f
Tube2 Gain
[dB] –24.0...+24.0 Sets the input gain for stage 2
Saturation [%] 0...100 Sets the input/output response for
stage 2
g Tube2 Bias 0...100 Sets the bias voltage for stage 2
hTube2 Outpu t
Level [dB] –48.0...+0.0 Sets the output level
i
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
+Tube Pre Amp1 Tube Pre Amp2
Left
Right
FX Amt
Output Level
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
–
+
Invert