140
Effects
Modulation and Pitch Shift (Mod./P.Shift)

value for the Feedback parameter, the pitch will be raised (or

lowered) more and more each time feedback is repeated.

If Feedback Position is set to Post, the feedback signal will not

pass through the pitch shifter again. Even if you specify a higher

value for the Feedback parameter, the pitch-shifted sound will

be repeated at the same pitch.

60: Pitch Shifter BPM

This pitch shifter enables you to set the delay time to match the

song tempo.

d: BPM

e: Delay Base Note

e: Times

The delay time is the duration of “Times” number of “Delay Base

Note” note values at the “BPM” tempo (or if “BPM” is set to

MIDI, the tempo determined by MIDI Clock).

d: Time Over?

You can set the delay time up to 5,290msec. If the delay time

exceeds this limit, the error message “OVER!” appears on the

display. Set the delay time parameters so that this message will

not appear. “Time Over?” is only a display parameter.

61: Pitch Shift Mod.(Pitch Shift Modulation)

This effect modulates the detuned pitch shift amou nt using an

LFO, adding a clear spread and width to the sound by panning

the effect sound and dry sound to the left and right. This is espe-

cially effective when the effect sound and dry sound output from

stereo speakers are mixed.

a: Pitch Shift [cents]

e: Depth

These parameters set the amount of pitch shift and amount of

modulation by means of the LFO.

g: Pan

h: Wet/Dry

The Pan parameter pans the effect sound and dry sound to the

left and right. With L, the effect sound is panned left, and the dry

sound is panned right. With a Wet/Dry = Wet setting, the effect

and dry sound will be output in a prop ortion of 1:1.

aMode Slow, Medium,
Fast
Switches Pitch Shifter mode
b
Pitch Shift [1/
2tone] –24...+24 Sets the pitch shift amount in steps
of a semitone
Src Off...Tempo Selects the modulation source of
pitch shift amount
Amt –24...+24 Sets the modulation amount of
pitch shift amount
c
Fine [cents] –100...+100 Sets the pitch shift amount in steps
of one cent
Amt –100...+100 Sets the modulation amount of
pitch shift amount
d
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Time Over? ---, OVER! Displays an error message when the
delay time exceeds the upper limit
e
Delay Base
Note r...w Selects the type of notes to specify
the delay time
Times x1...x32 Sets the number of notes to specify
the delay time
fFeedback
Position Pre, Post Switches the feedback
connection
g
Feedback –100...+100 Sets the feedback amount
High Damp [%] 0...100 Sets the damping amount in the
high range
h
Input Level
Dmod [%] –100...+100 Sets the modulation amount of the
input level
Src Off...Tempo Selects the modulation source for
the input level
i
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
BPM
BPM Base Note x Times
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Pitch Shifter
Feedback Position
Pre Post
Tempo
aPitch Shift
[cents] –100...+100 Sets the pitch difference from the
input signal
bLFO Waveform
Triangle,
Square Selects the LFO Waveform
c
LFO Frequency
[Hz] 0.02...20.00 Sets the speed of the LFO
Src Off...Tempo Selects a modulation source for LFO
speed
Amt –20.00...
+20.00
Sets the modulation amount of LFO
speed
d
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w Selects the type of notes that
specify the LFO speed
Times x1...x32 Sets the number of notes that
specify the LFO speed
e
Depth –100...+100 Sets the LFO modulation depth for
pitch shift amount
Src Off...Tempo Selects the modulation source of
the depth of modulation
Amt –100...+100 Sets the modulation amount of the
depth of modulation
fPan L, 1 : 99...99 : 1,
R
Sets the panning effect sound and
dry sound separately
g
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
LFO: Tri / Sqr
Pan
+
Pitch Shifter
Pitch
Higher
Pitch Shift Mod - Pitch Shift / Depth
Lower
Original Pitch Pitch Shift (+ value)
LFO Waveform=Triangle
Depth (+value)
LFO Waveform=Square
Depth (–value)