157
Effects
Mono-Mono Serial (Mono-Mono)
Advanced
94: Comp - Amp Sim(Compressor - Amp Simulation)

This effect combines a mono compressor and an amp simula-

tion. You can change the order of the effects.

95: Comp - OD/HiGain(Compressor - Overdrive/Hi.Gain)

This effect combines a mono compressor and an overdrive/high-

gain distortion. You can change the order of the effects.

COMPRESSOR
a[C]
Sensitivity 1...100 Sets the sensitivity
b[C]Attack 1...100 Sets the attack level
Output Level 0...100 Sets the compressor output level
c [C]EQ Trim 0...100 Sets the EQ input level
d
[C]Pre LEQ
Gain [dB] –15...+15 Sets the gain of Low EQ
Pre HEQ Gain
[dB] –15...+15 Sets the gain of High EQ
AMP SIM
e[A]Amplifier
Type SS, EL84, 6L6 Selects the type of guitar amplifier
fRouting Comp Amp,
Amp Comp
Switches the order of the
compressor and amp simulation
g
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
+
Compressor
Routing
Amp Simulation
Amp Simulation Filter
LEQ HEQ
EQ Trim
Output Level
Envelope - Control
Comp
COMPRESSOR
a[C]
Sensitivity 1...100 Sets the sensitivity
b[C]Attack 1...100 Sets the attack level
Output Level 0...100 Sets the compressor output level
OD/HI-GAIN
c
[O]
Drive Mode
Overdrive, Hi-
Gain
Switches between overdrive and
high-gain distortion
Drive 1...100 Sets the degree of distortion
d
[O]Output
Level 0...50 Sets the overdrive output level
Src Off...Tempo Selects the modulation source for
the overdrive output level
Amt –50...+50 Sets the modulation amount of the
overdrive output level
e
[O]Low Cutoff
[Hz] 20...1.00k Sets the center frequency for Low
EQ (shelving type)
Gain [dB] –18...+18 Sets the gain of Low EQ
f
[O]Mid1 Cutoff
[Hz] 300...10.00k Sets the center frequency for Mid/
High EQ 1 (peaking type)
Q 0.5...10.0 Sets the band width of Mid/High EQ
1
Gain [dB] –18...+18 Sets the gain of Mid/High EQ 1
g
[O]Mid2 Cutoff
[Hz] 500...20.00k Sets the center frequency for Mid/
High EQ 2 (peaking type)
Q 0.5...10.0 Sets the band width of Mid/High EQ
2
Gain [dB] –18...+18 Sets the gain of Mid/High EQ 2
h
[O]Wet/Dry
Dry,
1 : 99...99 : 1,
Wet
Sets the overdrive effect balance
Src Off...Tempo Selects the Wet/Dry modulation
source for the overdrive
Amt –100...+100 Sets the Wet/Dry modulation
amount for the overdrive
iRouting
Comp OD/
HG, OD/HG
Comp
Switches the order of the
compressor and overdrive
j
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
+
Routing
Overdrive / Hi-Gain
3 Band PEQ
Output Level
Mode: Overdrive / Hi-Gain
Drive
Driver
Compressor
Output Level
Envelope - Control
Comp
FX Amt