147
Effects
Delay
Advanced
a: Rec Mode
b: Reverse Time [msec]
When “Rec Mode” is set to Single, you can set up to 2,640msec
for “Reverse Time.” If recording starts during the reverse play-
back, the playback will be interrupted.
When “Rec Mo de” is set to Multi, you can make a nother rec ord-
ing during the reverse playback. However, the maximum
Reverse Time is limited to 1,320msec.
If you wish to record a phrase or rhyth m pattern, set “Rec Mode”
to Single. If you record only one note, set “Rec Mode” to Multi.
The “Reverse Time” parameter specifies the maximum duration
of the reverse playback. The part in excess of this limit will not
be played in reverse. If you wish to add short pieces of the
reverse playback of single notes, make the “Reverse Time”
shorter.
c: Envelope Select
c: Src
d: Threshold
These parameters select the source to control the start and end
of recording.
When “Envelope Select” is set to D-mod, the input signal will be
recorded only when the value of the modulation source selected
by the Src parameter is 64 or higher.
When “Envelope Select” is set to Input, the input signal will be
recorded only when its level exceeds the Threshold level.
When recording is completed, reverse playback st arts immedi-
ately.
73: Sequence BPM Dly(Sequence BPM Delay)
This four-tap delay enables you to select a tempo and rhythm
pattern to set up each tap.
a: BPM
b: Rhythm Pattern
With the tempo specified by the “BPM” parameter (or the MIDI
Clock tempo if “BPM” is set to MIDI), the length of one beat
equals the feedback delay time, and the interval between taps
becomes equal. Selecting a rhythm pattern will automatically
turn the tap outputs on and off. When “BPM” is set to MIDI, the
lower limit of the “BPM” is 44.
g
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
RecRec
Mode/Reverse Time
Input
Mode = Single
Mode = Multi
Time
Reverse Time Reverse Time
Envelope Select = Input
Reverse Reverse
aBPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
bRhythm
Pattern x...eee3Selects a rhythm pattern
c
Tap1 Pan L, 1...99, R Sets the panning of Tap1
Tap2 Pan L, 1...99, R Sets the panning of Tap2
Tap3 Pan L, 1...99, R Sets the panning of Tap3
Tap4 Pan L, 1...99, R Sets the panning of Tap4
d
Feedback –100...+100 Sets the feedback amount
Src Off...Tempo Selects the modulation source of
feedback amount
Amt –100...+100 Sets the feedback amount
e
High Damp [%] 0...100 Sets the damping amount in the
high range
Low Damp [%] 0...100 Sets the damping amount in the low
range
f
Input Level
Dmod [%] –100...+100 Sets the modulation amount of the
input level
Src Off...Tempo Selects the modulation source for
the input level
g
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
Delay
Left
Right
Feedback
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Input Level D-mod
High DampLow Damp
Input Level D-mod
+
Tempo
BPM
BPM
Rythm Pattern
Pan