177
Effects
Double Size
Advanced

a: Sw

This parameter determines how to switch on/off the overdrive

via a modulation source.

When “Sw” = Toggle, overdrive is turned on/off each time the

pedal or joystick is operated.

Overdrive will be switched on/off each time the value of the
modulation source exceeds 64.

When “Sw” = Moment, overdrive is applied only when you press

the pedal or operate the joystick.

Only when the value for the modulation source is 64 or higher, the
overdrive effect is applied.
134: L/C/R Long Delay

This multitap delay outputs three Tap signals to left, right and

center respectively. You can set a maximum of 5,460msec for the

delay time.

135: St/Cross Long Delay(Stereo/Cross Long Delay)

This is a stereo delay, and can by used as a cross-feedback delay

effect in which the delay sounds cross over between left and

right by changing the feedback routing. You can set a maximum

of 2,730msec for the delay time.

a
L Delay Time
[msec] 0...5460 Sets the delay time of TapL
Level 0...50 Sets the output level of TapL
b
C Delay Time
[msec] 0...5460 Sets the delay time of TapC
Level 0...50 Sets the output level of TapC
c
R Delay Time
[msec] 0...5460 Sets the delay time of TapR
Level 0...50 Sets the output level of TapR
d
Feedback
(C Delay) –100...+100 Sets the feedback amount of TapC
Src Off...Tempo Selects the modulation source for
the TapC feedback
Amt –100...+100 Sets the modulation amount of the
TapC feed bac k
e
High Damp [%] 0...100 Sets the damping amount in the
high range
Low Damp [%] 0...100 Sets the damping amount in the low
range
f
Input Level
Dmod [%] –100...+100 Sets the modulation amount of the
input level
Src Off...Tempo Selects the modulation source for
the input level
g Spread 0...50
Sets the width of the stereo image
of the effect sound
h
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
C Delay
R Delay
Left
Right
Feedback
Spread
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Input Level D-mod
High Damp Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level
a Stereo/Cross Stereo, Cross Switches between stereo delay and
cross-feedback delay
bL Delay Time
[msec] 0.0...2730.0 Sets the delay time for the left
channel
cR Delay Time
[msec] 0.0...2730.0 Sets the delay time for the right
channel
d
L Feedback –100...+100 Sets the feedback amount for the
left channel
Src Off...Tempo Selects the modulation source of
feedback amount
Amt –100...+100 Sets the modulation amount of the
left channel feedback
e
R Feedback –100...+100 Sets the feedback amount for the
right channel
Amt –100...+100 Sets the modulation amount of the
right channel feedback
f High Damp [%] 0...100 Sets the damping amount in the
high range
g Low Damp [%] 0...100 Sets the damping amount in the low
range
h
Input Level
Dmod [%] –100...+100 Sets the modulation amount of the
input level
Src Off...Tempo Selects the modulation source for
the input level
i Spread –50...+50
Sets the width of the stereo image of
the effect sound
j
Wet/Dry Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo Table, “Dynamic Modulation
sources,” on page106
Amt –100...+100 Amount of modulation source
Delay
Delay
Stereo/Cross
Left
Right
Feedback
FX Amt
FX Amt
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High DampLow Damp
Spread
Stereo/Cross