Lantronix Corporate Headquarters

Copyright and Trademark

DeviceLinx®, xPico™ and DeviceInstaller™ are trademarks of Lantronix.

Ethernet is a trademark of XEROX Corporation. UNIX is a registered trademark of The Open Group. Windows is a trademark of Microsoft Corp.

Warranty

For details on the Lantronix warranty policy, please go to our Web site at

www.lantronix.com/support/warranty.

Contacts

167 Technology Drive

Irvine, CA 92618, USA

Toll Free: 800-526-8766

Phone: 949-453-3995

Fax: 949-450-7249

Technical Support

Online: www.lantronix.com/support

Sales Offices

For a current list of our domestic and international sales offices, go to the Lantronix web site at www.lantronix.com/about/contact

xPico User Guide

Page 2

Image 2

Lantronix 900-618 manual Lantronix Corporate Headquarters, Technical Support Sales Offices

Contents

User Guide Lantronix Corporate Headquarters Technical Support Sales Offices Disclaimer Table of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Gpio Interface List of Tables List of Figures Chapter Summary Using This GuidePurpose and Audience Additional Documentation XPico Integration Guide Applications IntroductionCapabilities Addresses and Port Numbers Configuration MethodsProtocol Support Hardware Address Port Numbers Product Information LabelIP Address To install DeviceInstaller Using DeviceInstallerInstalling DeviceInstaller Assigning an IP Address Select Assign a specific IP address and click Next Accessing the xPico Using DeviceInstallerTo view the units current settings Name Comments Dhcp Device NameGroup Device Family Pins Firmware UpgradeableSupports Configurable Supports Http Setup Configuration Using Web Manager Accessing Web-Manager Using DeviceInstaller Network Configuration Web-Manager Login Window Select Obtain IP address automatically Network ModeTo assign an IP address automatically Select Use the following IP configuration Static IP Address ConfigurationEthernet Configuration To assign an IP address manually To configure the xPico’s device server settings Auto Negotiate Advanced Host List ConfigurationServer Configuration To configure the xPico’s host list Channel 1 and 2 ConfigurationRetry Settings Host Information To configure the channel’s serial settings Serial SettingsPort Settings Channel Pack Control Flush Input Buffer Serial to Network Flush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings At Time of Disconnect TCP Connection Settings Endpoint Configuration Connect Mode Passive ConnectionConnect Mode Active Connection Connect Protocol To configure a channel’s UDP settings Connection Settings UDPDisconnect Mode Use Broadcast Datagram ModeDatagram Type Device Address Table To configure the xPico’s Configurable Pins Configurable Pin SettingsConfigurable Pin Functions Serial Channel 1 Status LED Apply SettingsApply Defaults Serial Channel 2 Status LED Telnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode Serial Port Connection To establish a Telnet connection Exiting Setup Mode To exit setup mode BootP/DHCP/AutoIP Options Setup Mode Server ConfigurationServer Configuration Option IP Address Netmask Number of Bits for Host Part Change Telnet/Web-Manager PasswordSet Gateway IP Address Set DNS Server IP Address Dhcp Name Baudrate Setup Mode Channel ConfigurationChannel 1 Option 1 or Channel 2 Option RS232 Interface Mode Settings Interface ModeInterface Mode Options Flow Flow Control Options Connect ModePort Number Reserved Port Numbers Incoming Connection Connect Mode OptionsIncoming Connection Response Response Active Startup Manual Connection Manual Connection Address Example To enable the hostlist Hostlist Option Directed UDP Modem ModeDatagram Type Modem Mode Commands Numeric Response Auto Increment Source Port Send the Escape Sequence +++ in Modem ModeShow IP addr after Ring Disconnect Mode Options Remote IP Address Flush Mode Buffer Flushing Pack Control Send Characters Packing IntervalTrailing Characters Send Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal Type TCP Keepalive time in seconds Setup Mode Advanced SettingsExpert Settings Option CPU Performance ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port Number Enable alternate MAC Security Settings OptionTCP Re-Transmission Timeout Ethernet Connection Type Snmp Community Name Disable SnmpDisable Telnet Setup Disable Web Server Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Web Setup Enable Encryption To configure AES encryption on the xPico Disable Port 77F0 Hex Default Settings OptionEnable Enhanced Password Channel 1 and Channel 2 Configuration Defaults Hostlist retry timeout Expert Settings DefaultsSecurity Settings Defaults Start character for serial channel Gpio Interface Configurable PinsFeatures Control Protocol CommandsByte 0 Command Types Guidelines Command 12h, Get Active Levels Command 10h, Get FunctionsCommand 11h, Get Directions Command 13h, Get Current States Command 1Bh, Set States Command 19h, Set DirectionsCommand 1Ah, Set Active Levels Command details Response details Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface To download new firmware from a computer Using Tftp Command Line Interface Tftp Window To recover firmware Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode Commands S0, S1,...,Se, Sf Monitor Mode CommandsG0, G1, ....,Ge, Gf Example Command Response Codes Response Meaning Troubleshooting Problems and Error Messages Caps Lock is not on Lock on Troubleshooting Technical Support Europe, Middle East, and Africa Technical SupportTechnical Support US Conversion Table Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Scientific Calculator Binary to Hexadecimal Conversions Compliance RoHS Notice