Network Configuration, Web-Manager Login Window

4: Configuration Using Web Manager

Figure 4-1. Web-Manager Login Window

7. Perform one of the following:

If no Telnet password has been defined (default), leave both fields blank and click OK.

If a Telnet password has been defined, leave the username blank, type in the password, and then click OK.

The Web-Manager displays.

Figure 4-2. Lantronix Web-Manager

The main menu is in the left pane of the Web-Manager window.

Network Configuration

The unit’s network values display when you select Network from the main menu. The following sections describe the configurable parameters on the Network Settings page.

xPico User Guide

Page 19

Image 19

Lantronix 900-618 manual Network Configuration, Web-Manager Login Window

Contents

User Guide Technical Support Sales Offices Lantronix Corporate Headquarters Disclaimer Table of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Gpio Interface List of Figures List of Tables Purpose and Audience Using This GuideChapter Summary XPico Integration Guide Additional Documentation Capabilities IntroductionApplications Hardware Address Configuration MethodsProtocol Support Addresses and Port Numbers IP Address Product Information LabelPort Numbers Assigning an IP Address Using DeviceInstallerInstalling DeviceInstaller To install DeviceInstaller Name Accessing the xPico Using DeviceInstallerTo view the units current settings Select Assign a specific IP address and click Next Device Family Dhcp Device NameGroup Comments Supports Http Setup Firmware UpgradeableSupports Configurable Pins Accessing Web-Manager Using DeviceInstaller Configuration Using Web Manager Web-Manager Login Window Network Configuration To assign an IP address automatically Network ModeSelect Obtain IP address automatically To assign an IP address manually Static IP Address ConfigurationEthernet Configuration Select Use the following IP configuration Auto Negotiate To configure the xPico’s device server settings Server Configuration Host List ConfigurationAdvanced Host Information Channel 1 and 2 ConfigurationRetry Settings To configure the xPico’s host list Channel Serial SettingsPort Settings To configure the channel’s serial settings Flush Input Buffer Serial to Network Pack Control At Time of Disconnect Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to Serial TCP Connection Settings Connect Protocol Connect Mode Passive ConnectionConnect Mode Active Connection Endpoint Configuration Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings Device Address Table Datagram ModeDatagram Type Use Broadcast Configurable Pin Functions Configurable Pin SettingsTo configure the xPico’s Configurable Pins Serial Channel 2 Status LED Apply SettingsApply Defaults Serial Channel 1 Status LED Accessing Setup Mode Configuration via Telnet or Serial Port Setup ModeTelnet Connection To establish a Telnet connection Serial Port Connection To exit setup mode Exiting Setup Mode IP Address Setup Mode Server ConfigurationServer Configuration Option BootP/DHCP/AutoIP Options Set DNS Server IP Address Change Telnet/Web-Manager PasswordSet Gateway IP Address Netmask Number of Bits for Host Part Dhcp Name Channel 1 Option 1 or Channel 2 Option Setup Mode Channel ConfigurationBaudrate Flow Interface ModeInterface Mode Options RS232 Interface Mode Settings Reserved Port Numbers Connect ModePort Number Flow Control Options Response Connect Mode OptionsIncoming Connection Incoming Connection Active Startup Response Manual Connection Address Example Manual Connection Hostlist Option To enable the hostlist Datagram Type Modem ModeDirected UDP Numeric Response Modem Mode Commands Show IP addr after Ring Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote IP Address Disconnect Mode Options Pack Control Flush Mode Buffer Flushing Trailing Characters Packing IntervalSend Characters Telnet Terminal Type DisConnTime Inactivity TimeoutChannel Port Password Send Characters Expert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Http Port Number ARP Cache timeout in secondsDisable Monitor Mode at bootup CPU Performance Ethernet Connection Type Security Settings OptionTCP Re-Transmission Timeout Enable alternate MAC Disable Telnet Setup Disable SnmpSnmp Community Name Disable Web Setup Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Web Server To configure AES encryption on the xPico Enable Encryption Channel 1 and Channel 2 Configuration Defaults Default Settings OptionEnable Enhanced Password Disable Port 77F0 Hex Start character for serial channel Expert Settings DefaultsSecurity Settings Defaults Hostlist retry timeout Features Configurable PinsGpio Interface Guidelines CommandsByte 0 Command Types Control Protocol Command 13h, Get Current States Command 10h, Get FunctionsCommand 11h, Get Directions Command 12h, Get Active Levels Command details Command 19h, Set DirectionsCommand 1Ah, Set Active Levels Command 1Bh, Set States Response details To download new firmware from a computer Firmware UpgradesUsing Tftp Graphical User Interface Obtaining Firmware Reloading Firmware Tftp Window Using Tftp Command Line Interface To recover firmware Monitor Mode Commands Monitor ModeEntering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network Port Example Monitor Mode CommandsG0, G1, ....,Ge, Gf S0, S1,...,Se, Sf Response Meaning Command Response Codes Problems and Error Messages Troubleshooting Lock on Caps Lock is not on Troubleshooting Technical Support US Technical SupportTechnical Support Europe, Middle East, and Africa Scientific Calculator Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Conversion Table Binary to Hexadecimal Conversions RoHS Notice Compliance