Lantronix 900-618 Default Settings (Option 7)

8: Setup Mode: Advanced Settings

 Lantronix Secure Com Port Redirector provides an encrypted connection f rom

Windows-based applications to the xPico. Information about SCPR is at

www.lantronix.com/device-networking/utilities-tools/scpr

A 30-day trial version of SCPR is available.

Note: Developers can license the Lantronix Encryption Library Suite. See

www.lantronix.com/device-networking/utilities-tools.

Enable Enhanced Password

This setting defaults to the N (No) option, which allows you to set a 4-c haracter

password that protects Setup Mode by means of Telnet and web pages. T he Y (Yes)

option allows you to set an extended security password of 16-characters for

protecting Telnet and Web Page access.

Enable Enhanced Password (Y) ? _

Disable Port 77F0 (Hex)

Port 77F0 is a setting that allows a custom application to query or set the e ight xPico

configurable pins when they are functioning as general purpose I/O (GPIO) . You may

want to disable this capability for security purposes. The default sett ing is the N (No)

option, which enables GPIO control. The Y (Yes) option disables the GPIO co ntrol

interface.

Disable Port 77F0h ? _

Default Settings (Option 7)

Select 7 to reset the unit’s Channel 1 and Channel 2 configuration and expert

settings to the default settings. The server configuration settings f or IP address,

gateway IP address, and netmask remain unchanged. The configurable pins ’ settings

also remain unchanged. The specific settings that this option changes ar e listed

below:

Channel 1 and Channel 2 Configuration Defaults

Baudrate

9600

I/F Mode

4C (1 stop bit, no parity, 8 bit, RS-232C)

Flow

00

Note: Flow control option only available for

Channel 1 configuration.

Port number

10001 for Channel 1

10002 for Channel 2

Connect Mode

C0 (always accept incoming connection; no active

connection startup)

Send '+++' in Modem Mode

Enabled

Show IP addr after 'RING'

Enabled

Auto increment source port

Disable

Hostlist retry counter

3

xPico User Guide 60

Contents

Main Copyright and Trademark Warranty Contacts Disclaimer Revision History Table of Contents Page Page Page List of Tables List of Figures 1. Using This Guide xPico User Guide 9 Purpose and Audience Chapter Summary The remaining chapters in this guide include: Additional Documentation 2. Introduction Capabilities Applications Protocol Support Configuration Methods Addresses and Port Numbers Hardware Address IP Address Product Information Label 3. Using DeviceInstaller Installing DeviceInstaller Assigning an IP Address Accessing the xPico Using DeviceInstaller Viewing the Current Configuration 3: Using DeviceInstaller xPico User Guide 16 3: Using DeviceInstaller xPico User Guide 17 4. Configuration Using Web Manager Accessing Web-Manager Using DeviceInstaller Network Configuration Network Mode Automatic IP Address Configuration Static IP Address Configuration Ethernet Configuration Server Configuration 4: Configuration Using Web Manager Server Configuration Advanced Host List Configuration Retry Settings Host Information Channel 1 and 2 Configuration Serial Settings Channel 1 Port Settings 4: Configuration Using Web Manager Pack Control Flush Input Buffer (Serial to Network) Flush Output Buffer (Network to Serial) Connection Settings - TCP Page Connect Protocol xPico User Guide 29 Connect Mode: Passive Connection Connect Mode: Active Connection Endpoint Configuration Connection Settings - UDP Connect Protocol Datagram Mode Endpoint Configuration Configurable Pin Settings Configurable Pin Functions Apply Settings Apply Defaults 5. Configuration via Telnet or Serial Port (Setup Mode) Accessing Setup Mode Telnet Connection Serial Port Connection Exiting Setup Mode 6. Setup Mode: Server Configuration Server Configuration (Option 0) IP Address Set Gateway IP Address Netmask: Number of Bits for Host Part Set DNS Server IP Address Change Telnet/Web-Manager Password DHCP Name 7. Setup Mode: Channel Configuration Channel 1 (Option 1) or Channel 2 (Option 2) Baudrate 7: Setup Mode: Channel Configuration I/F (Interface) Mode Hex Binary Common I/F Mode Setting 1 Port Number Connect Mode 7: Setup Mode: Channel Configuration 1 2 a) Incoming Connection xPico User Guide 43 b) Response c) Active Startup 7: Setup Mode: Channel Configuration xPico User Guide 45 Command String Result if remote IP is 129.1.2.3 and remote port is 1234 Page d) Datagram Type e) Modem Mode Page Send the Escape Sequence (+++) in Modem Mode Show IP addr after 'RING' Auto Increment Source Port Remote IP Address Remote Port DisConnMode Flush Mode (Buffer Flushing) Pack Control Packing Interval Trailing Characters Send Characters DisConnTime (Inactivity Timeout) Send Characters Telnet Terminal Type Channel (Port) Password 8. Setup Mode: Advanced Settings Expert Settings (Option 5) TCP Keepalive time in seconds ARP Cache timeout in seconds CPU Performance Disable Monitor Mode at bootup HTTP Port Number MTU Size Security Settings (Option 6) Page Disable TFTP Firmware Upgrade Disable Port 77FE (Hex) Disable Web Server Disable Web Setup Disable ECHO Ports Enable Encryption Enable Enhanced Password Disable Port 77F0 (Hex) Default Settings (Option 7) Channel 1 and Channel 2 Configuration Defaults 8: Setup Mode: Advanced Settings Expert Settings Defaults xPico User Guide 61 Security Settings Defaults 9. GPIO Interface Configurable Pins Features Control Protocol Guidelines Commands Byte 0 Command Types 9: GPIO Interface Command 10h, Get Functions xPico User Guide 64 Command 11h, Get Directions Command 12h, Get Active Levels Command 13h, Get Current States Examples Page 10. Firmware Upgrades Obtaining Firmware Reloading Firmware Using TFTP: Graphical User Interface Using TFTP: Command Line Interface Recovering the Firmware Using the Serial Port and DeviceInstaller 11. Monitor Mode Entering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network Port Monitor Mode Commands 11: Monitor Mode Page 12. Troubleshooting xPico User Guide 73 Problems and Error Messages 12: Troubleshooting xPico User Guide 74 12: Troubleshooting xPico User Guide 75 Technical Support A: Binary to Hexadecimal Conversions Converting Binary to Hexadecimal Conversion Table Scientific Calculator Page B: Compliance RoHS Notice