Installing the UDS, To install the unit | Lantronix UDS1100 guide

3: Getting Started

Installing the UDS

Figure 3-1. UDS1100 Connected to Serial Device and Network

To install the unit:

Complete the following steps in order. Refer to the numbers in the figure above. Note: See the sections that follow for details about connectors and pinouts.

1.Connect a serial device to your unit.

2.Connect an Ethernet cable to the RJ45 port.

3.Supply power to your unit using the power supply that was included in the packaging.

Note: The required input voltage is 9-30 VDC (center +) or 10-24 VAC (1.5W maximum power required).

4.Supply power to the serial device.

Note: If you encounter a problem, please see LEDs on page 65 for diagnostic information.

UDS1100 User Guide

14

Image 14

Lantronix UDS1100 manual Installing the UDS, To install the unit

Contents

UDS1100 User Guide Revisions Copyright & TrademarkContacts Date Rev Comments 900-417 Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents Tables Chapter Summary Using This GuidePurpose and Audience Using This Guide Additional Documentation Application Examples IntroductionApplications Introduction Protocol Support Additional FeaturesConfiguration Methods Product Information Label Sample Hardware Address Package Contents Getting Started Installing the UDS To install the unit IP Address Required InformationHardware Address IP Address Subnet Mask Gateway Assigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click Next To view the units current settings Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage List IP Address on Assigning the IP Address Serial Port Login Next Step Getting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstaller Network Configuration Lantronix Web-Manager Automatic IP Address Configuration Static IP Address Configuration To specify how data will be transmitted Server ConfigurationEthernet Configuration Advanced To configure the UDS1100’s device server settingsServer Configuration Retry Settings Host List ConfigurationTo configure the host list To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Host Information Pack Control Port SettingsChannel Flush Input Buffer Serial to Network Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to Serial Connect Mode Passive Connection Connect Protocol Common Options Connect Mode Active ConnectionEndpoint Configuration To configure a channel’s UDP settings Connection Settings UDPDisconnect Mode Datagram Mode UDP Connection Settings Apply Settings Apply Factory Defaults Telnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connection Serial Port Connection Exiting Setup ModeTo exit setup mode IP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP Address Dhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits Netmask Setup Mode Server Configuration Baudrate Setup Mode Channel ConfigurationChannel 1 Option Common I/F Mode Setting Binary Interface ModeMode Option Flow Flow Control Option Hex Connect ModePort Number Port Numbers Reserved for Connect Mode Option Incoming Connection Response Active Startup Manual Connection Address Example Datagram Type Modem ModeTo enable the hostlist MessageMeaning No Carrier Modem Mode Function Command ATD Remote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote Port Flush Mode Buffer Flushing Disconnect Mode Option Pack Control Option Packing Interval DisConnTime Inactivity TimeoutSend Characters Trailing Characters Channel Port Password Telnet Terminal Type TCP Keepalive time in seconds Setup Mode Advanced SettingsExpert Settings Option Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port Number Disable Telnet Setup Security Settings OptionDisable Snmp Snmp Community Name Disable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web Setup Expert Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Security Settings Defaults Setup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM File Using Tftp Command Line Interface To recover firmware Firmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode Commands Command Command Name Function Response Meaning Troubleshooting and Contact Information LEDs Problems and Error Messages Problem/Message Reason Solution Lock on Technical Support Technical Support Europe, Middle East, and Africa Serial Port Serial Connector PinoutsConnections and Pinouts DB25 Female Interface RS422 4 wire mode Modem Cable Network Port Null Modem Cable Lantronix Part No Ethernet Connector Pinouts Power Plug Technical Specifications Category Description Technical Specifications Alternative Ways to Assign an IP Address AutoIP ARP and Telnet To assign a temporary IP address Decimal Binary Hex Converting Binary to HexadecimalConversion Table Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide