IP Address on | Lantronix UDS1100 specs

		3: Getting Started

	Type	Non-configurable field. Displays the device type as UDS1100.

	ID	Non-configurable field. Displays the UDS1100’s ID embedded
		within the box.

	Hardware Address	Non-configurable field. Displays the UDS1100’s hardware (or
		MAC) address.

	Firmware Version	Non-configurable field. Displays the firmware currently
		installed on the UDS1100.

	Extended Firmware	Non-configurable field. Displays the full version nomenclature
	Version	of the firmware.

	Online Status	Non-configurable field. Displays the UDS1100’s status as
		online, offline, unreachable (the UDS1100 is on a different
		subnet), or busy (the UDS1100 is currently performing a task).

	Telnet Enabled	Non-configurable field. Permits Telnet sessions.

	Telnet Port	Non-configurable field. Displays the UDS1100’s port for telnet
		sessions.

	Web Enabled	Non-configurable field. Permits configuration through Web-
		Manager.

	Web Port	Non-configurable field. Displays the UDS1100’s port for Web-
		Manager configuration.

	Maximum Baud Rate	Non-configurable field. Displays the UDS1100’s maximum
	Supported	baud rate.
		Note: The UDS1100 may not currently be running at this rate.

	Firmware Upgradeable	Non-configurable field. Displays True, indicating the
		UDS1100’s firmware is upgradeable as newer version
		become available.

	IP Address	Non-configurable field. Displays the UDS1100’s current IP
		address. To change the IP address, see Assigning an IP
		Address on page 16.

	Number of COB partitions	Non-configurable field. Displays the number of COB partitions
	supported	supported.

	Supports Dynamic IP	Non-configurable field. Indicates whether the current IP
		address on the UDS1100 was set manually or assigned by
		DHCP.

	Subnet Mask	Non-configurable field. Displays the UDS1100’s current
		subnet mask. To change the subnet mask, see Assigning an
		IP Address on page 16.

	Gateway	Non-configurable field. Displays the UDS1100’s current
		gateway. To change the gateway, see Assigning an IP
		Address on page 16.

	Number of Ports	Non-configurable field. Displays the number of ports on the
		UDS1100.

	TCP Keepalive	Non-configurable field. Displays the UDS1100’s TCP
		keepalive value. The value is in the range 1-65s, and the
		default setting is 45.

UDS1100 User Guide

18

Image 18

Lantronix UDS1100 manual IP Address on

Contents

UDS1100 User Guide Revisions Copyright & TrademarkContacts Date Rev Comments 900-417 Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents Tables Using This Guide Purpose and AudienceChapter Summary Using This Guide Additional Documentation Introduction ApplicationsApplication Examples Introduction Additional Features Configuration MethodsProtocol Support Product Information Label Sample Hardware Address Package Contents Getting Started Installing the UDS To install the unit IP Address Required InformationHardware Address IP Address Subnet Mask Gateway Assigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click Next To view the units current settings Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage List IP Address on Assigning the IP Address Serial Port Login Next Step Getting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstaller Network Configuration Lantronix Web-Manager Automatic IP Address Configuration Static IP Address Configuration Server Configuration Ethernet ConfigurationTo specify how data will be transmitted To configure the UDS1100’s device server settings Server ConfigurationAdvanced Host List Configuration To configure the host listRetry Settings To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Host Information Port Settings ChannelPack Control Flush Input Buffer Serial to Network Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to Serial Connect Mode Passive Connection Connect Protocol Connect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Datagram Mode UDP Connection Settings Apply Settings Apply Factory Defaults Telnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connection Exiting Setup Mode To exit setup modeSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP Address Dhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits Netmask Setup Mode Server Configuration Setup Mode Channel Configuration Channel 1 OptionBaudrate Common I/F Mode Setting Binary Interface ModeMode Option Flow Flow Control Option Hex Connect ModePort Number Port Numbers Reserved for Connect Mode Option Incoming Connection Response Active Startup Manual Connection Address Example Modem Mode To enable the hostlistDatagram Type MessageMeaning No Carrier Modem Mode Function Command ATD Remote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote Port Flush Mode Buffer Flushing Disconnect Mode Option Pack Control Option Packing Interval DisConnTime Inactivity TimeoutSend Characters Trailing Characters Channel Port Password Telnet Terminal Type Setup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port Number Disable Telnet Setup Security Settings OptionDisable Snmp Snmp Community Name Disable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web Setup Expert Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Security Settings Defaults Setup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM File Using Tftp Command Line Interface To recover firmware Firmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode Commands Command Command Name Function Response Meaning Troubleshooting and Contact Information LEDs Problems and Error Messages Problem/Message Reason Solution Lock on Technical Support Technical Support Europe, Middle East, and Africa Serial Connector Pinouts Connections and PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem Cable Network Port Null Modem Cable Lantronix Part No Ethernet Connector Pinouts Power Plug Technical Specifications Category Description Technical Specifications Alternative Ways to Assign an IP Address AutoIP ARP and Telnet To assign a temporary IP address Converting Binary to Hexadecimal Conversion TableDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide