Using Tftp Command Line Interface | Lantronix UDS1100 instruction

9: Firmware Upgrades

Figure 9-1. TFTP Window

After the firmware has been loaded and stored, which takes approximately 8 seconds to complete, the unit performs a power reset.

Using TFTP: Command Line Interface

To download new firmware from a computer:

1.Enter the following from a TFTP command line interface:

tftp –i <ip address> put <local filename> <destination file name>

The following examples demonstrate the TFTP command sequence to download the .rom file and the .cob file:

tftp –i 192.168.1.111 put uds1100_6101.rom U3 tftp –i 192.168.1.111 put uds1100_webm_1401.cob WEB4

2.In the Remote file name field, enter the current internal operational code (U3) or WEB1 to WEB19 for the internal Web interface.

Recovering the Firmware Using the Serial Port and DeviceInstaller

If for some reason the firmware is damaged, you can recover the firmware file by using DeviceInstaller to download the *.ROM file over the serial port.

To recover firmware:

1.Start DeviceInstaller. If your PC has more than one network adapter, a message displays. Select an adapter and click OK.

2.From the Tools menu, select Advanced/Recover Firmware. The Serial Port Firmware Upgrade window displays.

3.For Port on PC, enter the COM port on the PC that is connected to the serial port of the Lantronix unit.

4.For Device Model, be sure the appropriate device (e.g., UDS1100) displays.

UDS1100 User Guide

61

Image 61

Lantronix UDS1100 manual Using Tftp Command Line Interface, To recover firmware

Contents

UDS1100 User Guide Contacts Copyright & TrademarkRevisions Date Rev Comments 900-417 Contents Setup Mode Server Configuration Troubleshooting and Contact Information Tables Contents Purpose and Audience Using This GuideChapter Summary Additional Documentation Using This Guide Applications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Sample Hardware Address Product Information Label Getting Started Package Contents To install the unit Installing the UDS Hardware Address Required InformationIP Address IP Address Subnet Mask Gateway Installing DeviceInstaller Assigning the IP Address DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click Next Viewing the Current Configuration Accessing the UDS1100 Using DeviceInstallerTo view the units current settings Adding the Unit to the Manage List IP Address on Next Step Assigning the IP Address Serial Port Login Getting Started Accessing UDS1100 Using DeviceInstaller Configuration Using Web-Manager Lantronix Web-Manager Network Configuration Static IP Address Configuration Automatic IP Address Configuration Ethernet Configuration Server ConfigurationTo specify how data will be transmitted Server Configuration To configure the UDS1100’s device server settingsAdvanced To configure the host list Host List ConfigurationRetry Settings Serial Settings Channel 1 ConfigurationTo configure the channel’s serial settings Host Information Channel Port SettingsPack Control To configure a channel’s TCP settings Connection Settings TCPFlush Input Buffer Serial to Network Flush Output Buffer Network to Serial Connect Protocol Connect Mode Passive Connection Endpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings UDP Connection Settings Datagram Mode Apply Factory Defaults Apply Settings Accessing Setup Mode Configuration via Telnet or Serial Port Setup ModeTelnet Connection To establish a Telnet connection To exit setup mode Exiting Setup ModeSerial Port Connection Server Configuration Option Setup Mode Server ConfigurationIP Address Set Gateway IP Address Netmask Number of Bits for Host Part Change Telnet Configuration PasswordDhcp Name Network Class Host Bits Netmask Setup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Mode Option Interface ModeCommon I/F Mode Setting Binary Flow Port Number Connect ModeFlow Control Option Hex Port Numbers Reserved for Incoming Connection Connect Mode Option Active Startup Response Manual Connection Address Example To enable the hostlist Modem ModeDatagram Type No Carrier MessageMeaning ATD Modem Mode Function Command Auto Increment Source Port Send the Escape Sequence +++ in Modem ModeRemote IP Address Remote Port Disconnect Mode Option Flush Mode Buffer Flushing Option Pack Control Send Characters DisConnTime Inactivity TimeoutPacking Interval Trailing Characters Telnet Terminal Type Channel Port Password Expert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Disable Monitor Mode at bootup ARP Cache timeout in secondsEnable alternate MAC Http Port Number Disable Snmp Security Settings OptionDisable Telnet Setup Snmp Community Name Disable Port 77FE Hex Disable Tftp Firmware UpdateDisable Web Server Disable Web Setup Channel 1 Configuration Defaults Default Settings OptionExpert Settings Defaults Security Settings Defaults Setup Mode Advanced Settings Using Tftp Graphical User Interface Firmware UpgradesObtaining Firmware Reloading Firmware ROM File To recover firmware Using Tftp Command Line Interface Firmware Upgrades Entering Monitor Mode Using the Serial Port Monitor ModeEntering Monitor Mode Using the Network Port Monitor Mode Commands Response Meaning Command Command Name Function LEDs Troubleshooting and Contact Information Problem/Message Reason Solution Problems and Error Messages Lock on Technical Support Europe, Middle East, and Africa Technical Support Connections and Pinouts Serial Connector PinoutsSerial Port Modem Cable DB25 Female Interface RS422 4 wire mode Null Modem Cable Lantronix Part No Network Port Power Plug Ethernet Connector Pinouts Category Description Technical Specifications Technical Specifications AutoIP Alternative Ways to Assign an IP Address To assign a temporary IP address ARP and Telnet Conversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide