Ethernet Connector Pinouts, Power Plug | Lantronix UDS1100 specification

12: Connections and Pinouts

Ethernet Connector Pinouts

The UDS1100 supports 10/100 Mbps half or full duplex Ethernet through an RJ45 connector.

Figure 12-7. RJ45 Ethernet Connector

g

Power Plug

Power input on the power plug is 9 -30 VDC (center +) or 10-24 VAC (1.5W maximum power required).

UDS1100 User Guide

72

Image 72

Lantronix UDS1100 manual Ethernet Connector Pinouts, Power Plug

Contents

UDS1100 User Guide Copyright & Trademark ContactsRevisions Date Rev Comments 900-417 Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents Tables Using This Guide Purpose and AudienceChapter Summary Using This Guide Additional Documentation Introduction ApplicationsApplication Examples Introduction Additional Features Configuration MethodsProtocol Support Product Information Label Sample Hardware Address Package Contents Getting Started Installing the UDS To install the unit Required Information Hardware AddressIP Address IP Address Subnet Mask Gateway Assigning the IP Address DeviceInstaller Installing DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click Next Accessing the UDS1100 Using DeviceInstaller Viewing the Current ConfigurationTo view the units current settings Adding the Unit to the Manage List IP Address on Assigning the IP Address Serial Port Login Next Step Getting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstaller Network Configuration Lantronix Web-Manager Automatic IP Address Configuration Static IP Address Configuration Server Configuration Ethernet ConfigurationTo specify how data will be transmitted To configure the UDS1100’s device server settings Server ConfigurationAdvanced Host List Configuration To configure the host listRetry Settings Channel 1 Configuration Serial SettingsTo configure the channel’s serial settings Host Information Port Settings ChannelPack Control Connection Settings TCP To configure a channel’s TCP settingsFlush Input Buffer Serial to Network Flush Output Buffer Network to Serial Connect Mode Passive Connection Connect Protocol Connect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Datagram Mode UDP Connection Settings Apply Settings Apply Factory Defaults Configuration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connection Exiting Setup Mode To exit setup modeSerial Port Connection Setup Mode Server Configuration Server Configuration OptionIP Address Set Gateway IP Address Change Telnet Configuration Password Netmask Number of Bits for Host PartDhcp Name Network Class Host Bits Netmask Setup Mode Server Configuration Setup Mode Channel Configuration Channel 1 OptionBaudrate Interface Mode Mode OptionCommon I/F Mode Setting Binary Flow Connect Mode Port NumberFlow Control Option Hex Port Numbers Reserved for Connect Mode Option Incoming Connection Response Active Startup Manual Connection Address Example Modem Mode To enable the hostlistDatagram Type MessageMeaning No Carrier Modem Mode Function Command ATD Send the Escape Sequence +++ in Modem Mode Auto Increment Source PortRemote IP Address Remote Port Flush Mode Buffer Flushing Disconnect Mode Option Pack Control Option DisConnTime Inactivity Timeout Send CharactersPacking Interval Trailing Characters Channel Port Password Telnet Terminal Type Setup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds ARP Cache timeout in seconds Disable Monitor Mode at bootupEnable alternate MAC Http Port Number Security Settings Option Disable SnmpDisable Telnet Setup Snmp Community Name Disable Tftp Firmware Update Disable Port 77FE HexDisable Web Server Disable Web Setup Default Settings Option Channel 1 Configuration DefaultsExpert Settings Defaults Security Settings Defaults Setup Mode Advanced Settings Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM File Using Tftp Command Line Interface To recover firmware Firmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode Commands Command Command Name Function Response Meaning Troubleshooting and Contact Information LEDs Problems and Error Messages Problem/Message Reason Solution Lock on Technical Support Technical Support Europe, Middle East, and Africa Serial Connector Pinouts Connections and PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem Cable Network Port Null Modem Cable Lantronix Part No Ethernet Connector Pinouts Power Plug Technical Specifications Category Description Technical Specifications Alternative Ways to Assign an IP Address AutoIP ARP and Telnet To assign a temporary IP address Converting Binary to Hexadecimal Conversion TableDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide