Manuals / Lantronix / Computer Equipment / Network Card

Lantronix UDS1100 manual Modem Cable, DB25 Female Interface RS422 4 wire mode

Models: UDS1100

1 83

Download 83 pages 59.79 Kb

Page 70

Image 70

12: Connections and Pinouts

Figure 12-3. DB25 Female Interface RS422 (4 wire mode)

Figure 12-4. DB25 Female Interface RS485 (2 wire mode)

Modem Cable

When attaching the DB25 of the UDS to the DB9 com port on a PC, use a standard straight-through serial cable (Lantronix Part No. 500-163). The figure below shows the pinouts for a DB25 to DB9 straight-through cable, often referred to as a "Modem Cable".

To configure the UDS using the DB9 serial port, you need only pin out the TXD, RXD, and GND signals.

UDS1100 User Guide

Page 70

Image 70

Lantronix UDS1100 manual Modem Cable, DB25 Female Interface RS422 4 wire mode

Contents

UDS1100 User Guide Revisions Copyright & TrademarkContacts Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesPurpose and Audience Using This GuideChapter Summary Using This Guide Additional DocumentationApplications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitIP Address Required InformationHardware Address IP Address Subnet Mask GatewayAssigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click NextTo view the units current settings Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationEthernet Configuration Server ConfigurationTo specify how data will be transmitted Server Configuration To configure the UDS1100’s device server settingsAdvanced To configure the host list Host List ConfigurationRetry Settings To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Host InformationChannel Port SettingsPack Control Flush Input Buffer Serial to Network Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolEndpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connectionTo exit setup mode Exiting Setup ModeSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP AddressDhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits NetmaskSetup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Common I/F Mode Setting Binary Interface ModeMode Option FlowFlow Control Option Hex Connect ModePort Number Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example To enable the hostlist Modem ModeDatagram Type MessageMeaning No CarrierModem Mode Function Command ATDRemote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionPacking Interval DisConnTime Inactivity TimeoutSend Characters Trailing CharactersChannel Port Password Telnet Terminal TypeExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberDisable Telnet Setup Security Settings OptionDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web SetupExpert Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Security Settings DefaultsSetup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaConnections and Pinouts Serial Connector PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressConversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide