Setup Mode Channel Configuration, Baudrate | Lantronix UDS1100

7: Setup Mode: Channel Configuration

This chapter explains how to configure the serial port.

Notes:

Current values display in parenthesis.

You must enter some values in hexadecimal notation. (See B: Binary to Hexadecimal Conversions.)

Channel 1 (Option 1)

Select Channel 1 (option 1) from the Change Setup menu to define how the serial port responds to network and serial communications. The following sections describe the configurable parameters within the Channel configuration menu.

Figure 7-1. Serial Port Settings

Baudrate

The unit and attached serial device, such as a modem, must agree on a speed or baud rate to use for the serial connection. Valid baud rates are 300, 600, 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, 115200, and 230400 baud.

Baudrate (9600) ? _

UDS1100 User Guide

40

Image 40

Lantronix UDS1100 manual Setup Mode Channel Configuration, Channel 1 Option, Baudrate

Contents

UDS1100 User Guide Copyright & Trademark ContactsRevisions Date Rev Comments 900-417 Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents Tables Purpose and Audience Using This GuideChapter Summary Using This Guide Additional Documentation Applications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Product Information Label Sample Hardware Address Package Contents Getting Started Installing the UDS To install the unit Required Information Hardware AddressIP Address IP Address Subnet Mask Gateway Assigning the IP Address DeviceInstaller Installing DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click Next Accessing the UDS1100 Using DeviceInstaller Viewing the Current ConfigurationTo view the units current settings Adding the Unit to the Manage List IP Address on Assigning the IP Address Serial Port Login Next Step Getting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstaller Network Configuration Lantronix Web-Manager Automatic IP Address Configuration Static IP Address Configuration Ethernet Configuration Server ConfigurationTo specify how data will be transmitted Server Configuration To configure the UDS1100’s device server settingsAdvanced To configure the host list Host List ConfigurationRetry Settings Channel 1 Configuration Serial SettingsTo configure the channel’s serial settings Host Information Channel Port SettingsPack Control Connection Settings TCP To configure a channel’s TCP settingsFlush Input Buffer Serial to Network Flush Output Buffer Network to Serial Connect Mode Passive Connection Connect Protocol Endpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings Datagram Mode UDP Connection Settings Apply Settings Apply Factory Defaults Configuration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connection To exit setup mode Exiting Setup ModeSerial Port Connection Setup Mode Server Configuration Server Configuration OptionIP Address Set Gateway IP Address Change Telnet Configuration Password Netmask Number of Bits for Host PartDhcp Name Network Class Host Bits Netmask Setup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Interface Mode Mode OptionCommon I/F Mode Setting Binary Flow Connect Mode Port NumberFlow Control Option Hex Port Numbers Reserved for Connect Mode Option Incoming Connection Response Active Startup Manual Connection Address Example To enable the hostlist Modem ModeDatagram Type MessageMeaning No Carrier Modem Mode Function Command ATD Send the Escape Sequence +++ in Modem Mode Auto Increment Source PortRemote IP Address Remote Port Flush Mode Buffer Flushing Disconnect Mode Option Pack Control Option DisConnTime Inactivity Timeout Send CharactersPacking Interval Trailing Characters Channel Port Password Telnet Terminal Type Expert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds ARP Cache timeout in seconds Disable Monitor Mode at bootupEnable alternate MAC Http Port Number Security Settings Option Disable SnmpDisable Telnet Setup Snmp Community Name Disable Tftp Firmware Update Disable Port 77FE HexDisable Web Server Disable Web Setup Default Settings Option Channel 1 Configuration DefaultsExpert Settings Defaults Security Settings Defaults Setup Mode Advanced Settings Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM File Using Tftp Command Line Interface To recover firmware Firmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode Commands Command Command Name Function Response Meaning Troubleshooting and Contact Information LEDs Problems and Error Messages Problem/Message Reason Solution Lock on Technical Support Technical Support Europe, Middle East, and Africa Connections and Pinouts Serial Connector PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem Cable Network Port Null Modem Cable Lantronix Part No Ethernet Connector Pinouts Power Plug Technical Specifications Category Description Technical Specifications Alternative Ways to Assign an IP Address AutoIP ARP and Telnet To assign a temporary IP address Conversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide