SOFTWARE INSTALLATION | Section 2 |
2.4 EQUIPMENT/SOFTWARE STARTUP
When the Wave Designer software installation is complete, Wave Designer is listed among the programs you can start up from the Windows startup screen. Click on START, point to the programs option, then click on the Wave Designer option. The Wave Designer Welcome screen is displayed followed by the Pulse Waveform Editor screen. When the Pulse Waveform Editor screen is displayed, the software is ready for use.
Wave Designer Pro Off Line - pulse.swf
File Tools Print Help
Pulse Waveform Editor | 700 |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| ||||
Wire Feed Speed | 50 | Edit | 600 |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||||
Ramp Up Rate | 600 |
| 500 |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Ramp Overshoot % |
| 400 |
|
|
|
|
|
|
|
|
|
| |||
Peak Amps | 250 |
| 300 |
|
|
|
|
|
|
|
|
|
| ||
Peak Time ms | 1.2 |
| 200 |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Tailout Time | 3.0 |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 100 |
|
|
|
|
|
|
|
|
|
| |
Tailout Speed | .100 |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Stepoff Amps | 40 |
| 0 | 0 | 3 | 6 | 9 | 12 | 15 | 18 | 21 | 24 | 27 | 30 | |
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Backgrd Amps | 21 |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Backgrd Time | 33.4 |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Frequency | 26.4 |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Start | Adapt | Short | End |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||||
| About |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||||||
Status | AC.sco loaded |
|
|
|
|
|
| Off Line | Stand by | Adaptive |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 27850001 |
2.5 UPGRADE FIRMWARE
An ArcScope application is provided with Wave Designer Pro. In order to run the ArcScope application, it may be necessary to upgrade the welding machine firmware. If the old firmware does not support ArcScope, the ArcScope application will display garbled data rather than waveforms. Wave Designer will automatically detect the firmware version and prompt you to upgrade the firmware if required.
WAVE DESIGNER
