ADDING ADDITIONAL USER CODES
✦The Console can be programmed with five restricted user codes and one page alert user code.
✦The restricted user codes operate the system as usual, but cannot access Setup Mode.
✦The restricted user codes can access a special Code Mode that can be used to change or remove any of the fi ve restricted user codes, the page alert user code, or the duress code.
✦The page alert user code dials the supervisory number (programmed for a pager) when it is used to arm or disarm the system.
✦A restricted user code is appropriate to give any user that should be restricted from programming the Console.
✎NOTE: For maximum security, a
✎WARNING: NEVER PROGRAM ANY RESTRICTED USER CODETHE SAME ASTHE MASTER USER CODE!
STEPS
PROGRAMMING STEPS #93 TO 98
PROGRAM
STORE PROGRAM
STEP | CODE FUNCTION | CODE ENTERED |
STEP #93 | RESTRICTED USER CODE #1 |
|
|
|
|
STEP #94 | RESTRICTED USER CODE #2 |
|
|
|
|
STEP #95 | RESTRICTED USER CODE #3 |
|
|
|
|
STEP #96 | RESTRICTED USER CODE #4 |
|
|
|
|
STEP #97 | RESTRICTED USER CODE #5 |
|
|
|
|
STEP #98 | PAGE ALERT USER CODE |
|
|
|
|
REMOVING ADDITIONAL USER CODES |
|
| |
| KEYPAD CODE | ||
STEPS | 9 WXY | ||
| PROGRAMMING STEPS | ||
from the Console by entering the appropriate step |
| ||
| #92 TO 98 | ||
number and pressing TEST. | TEST | REMOVE | |
✦ Because access to programming would be impossible | |||
|
| ||
without a master user code, it cannot be removed |
|
| |
using these steps. The master user code can be |
|
| |
changed using programming STEP #99. |
|
|
✎NOTE: The master user code can be set to the factory default using the Console master reset programming step, although all other system programming will be reset to factory values and all sensors programmed will be erased.
CONSOLE MASTER RESET |
|
|
| |
START IN TEST |
| |||
✦ Master resetting the Console will set all of the |
| |||
|
|
| ||
| programming options back to the factory values. The |
| MASTER |
|
| master user code will be reset to 1234. |
|
| |
|
| USER |
| |
|
|
|
| |
✎ CAUTION: Master resetting the Console will erase the |
| CODE |
| |
| user codes and remove all programmed sensors. All |
|
|
|
| Console and communicator programming values will |
| 1 GONG & |
|
| be reset to the factory defaults. | TEST |
| |
| 5 BEEPS |
| ||
1. Start with the system in Test Mode (Setup Mode |
|
| ||
|
|
| ||
| cannot be reached from any other mode). | 9 WXY | STEP #999 |
|
2. | From Test Mode, enter the master user code then |
|
| |
9 WXY | FOR | USE THESE EXACT | ||
| press TEST. |
| MASTER | |
|
| KEYSTROKES | ||
|
| RESET | ||
|
|
| TO PERFORM A | |
| ✴ A “Gong” and fi ve “Beeps” will sound, signaling that the | 9 WXY |
| |
|
| MASTER RESET | ||
|
|
| ||
| system is in Setup Mode. |
| PRESS |
|
3. | Enter programming STEP #999 then press TEST. | TEST |
| |
TEST |
| |||
|
|
4.Enter 999 again then press TEST again.
|
| 9 WXY |
|
| ✴ A “Bing” will sound to indicate the beginning of the reset |
| ENTER 999 |
| 9 WXY | TO OK THE | |
| process. This process will take up to 10 seconds while the | ||
|
| MASTER | |
| memory is being reset. | 9 WXY | RESET |
✦ | The system will revert to the first time |
| |
| PRESS TEST, | ||
| condition and the new master user code will be 1234. |
| |
| TEST | 1 BING SOUNDS, | |
| Go to the “Basic Console Programming” section of | WAIT ABOUT 10 | |
|
| ||
| this manual to begin |
| SECONDS |
| DONE | ||
|
|
31