Manuals / Linear / Household Appliance / Home Security System

Linear DVS-2400 4 BY 2 FORMAT POINT ID REPORTING CODES, 4 BY 2 FORMAT POINT ID ALARM REPORT CODES

Models: DVS-2400

1 44

Download 44 pages 42.75 Kb

Page 42

4 BY 2 FORMAT POINT ID REPORTING CODES

4 BY 2 FORMAT POINT ID REPORTING CODES

4 BY 2 FORMAT POINT ID ALARM REPORT CODES

✦Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the alarm reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled and any sensor triggers an alarm. The factory settings are listed, along with a blank area to write in the new installation values.

✦Use program Steps #210 - 233 to change the 4 by 2 Point ID alarm reporting codes.

✎NOTE: Be careful not to duplicate codes unless the Central Station requires speciﬁc codes for certain types of sensors.

2ABC

PROGRAMMING STEPS #210 TO #233

PROGRAM

0 - 99 FOR SENSOR ALARM CODE

(0 = NO REPORT)

STORE PROGRAM

STEPS #210-233

Any value from 0-99 can be programmed for each event using these steps (enter “0” to stop an event from reporting).

4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES

✦Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the trouble reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled and any sensor has a low battery or trouble condition. The factory settings are listed, along with a blank area to write in the new installation values.

✦Use program Steps #234 - 257 to change the 4 by 2 Point ID trouble reporting codes.

✎NOTE: Be careful not to duplicate codes unless the Central Station requires speciﬁc codes for certain types of sensors.

2ABC

PROGRAMMING STEPS #234 TO #257

PROGRAM

0 - 99 FOR SENSOR TROUBLE CODE (0 = NO REPORT)

STORE PROGRAM

STEPS #234-257

Any value from 0-99 can be programmed for each event using these steps (enter “0” to stop an event from reporting).

40

Image 42

Linear DVS-2400 manual 4 BY 2 FORMAT POINT ID REPORTING CODES, 4 BY 2 FORMAT POINT ID ALARM REPORT CODES, STEPS #210-233

Contents

SECURITY SUPERVISED WIRELESS SECURITY CONSOLEInstallation & Programming Instructions USA & CanadaThis symbol is for important notes INTRODUCTIONTABLE OF CONTENTS 1.THE DVS-2400SECURITY SYSTEM CONSOLEDOOR/WINDOW SENSORS WIRELESS KEYPADREMOTE CONTROLS SMOKE DETECTOREXAMPLE SYSTEM DESIGN THE INSTALLATION2.SECURITY SYSTEM FLOOR PLAN Example Residential Security System Floor PlanABOUT SENSOR STATUS SUPERVISION 3.TYPICAL SYSTEM SENSORSDOOR/WINDOW SENSOR WIRELESS KEYPADSwitching to Off Mode stops the alarm siren 4.CONSOLE FEATURES5 4 3 Switching to Chime Mode stops the alarm sirenType 2AG, 1-ampfuse CASE LOCKING SCREW 5.CONSOLE INSTALLATIONCONSOLE LOCATION WALL MOUNTINGEXTERNAL CONSOLE SPEAKER CONNECTION EXTERNAL ALARM SIREN CONNECTIONcan talk to the occupants through the external TELEPHONE LINE CONNECTION AUTOMATION OUTPUT CONNECTION OPTIONALConnect the Console to the telephone line if the BACKUP BATTERY INSTALLATION OPTIONAL CONSOLE POWER CONNECTIONnot plug the transformer in until the wiring is completeSTART IN TEST indicator for that sensor will stay lit6.BASIC CONSOLE PROGRAMMING MASTER USER CODE 1 GONG & 5 BEEPSselect a sensor number to program the sensor into PROGRAMMING DIFFERENT SENSOR TYPESFollow the instructions on the previous page to For DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62A7.BASIC SENSOR INSTALLATION DXS-10WIRELESS KEYPADDXS-31& DXS-32DOOR/WINDOW SENSORS TEST SENSORS4.Snap sensor onto mounting plate 8.CUSTOMIZING THE CONSOLE LABELING THE SENSORS9.CONSOLE OPERATING MODES and stops any alarms in progresscaused the alarm will ﬂ ash OFF MODESTART IN OFF OR CHIME MODE HOME MODESECURE EXIT START IN HOME MODEAWAY MODE EXIT DELAY For Leaving the PremisesENTRY DELAY For Entering the Premises QUICK ARMTEST MODE 3 beeps being the strongest signalstatus indicators START IN OFFSENSOR LOW BATTERIES CONSOLE LOW BATTERY10.SYSTEM TROUBLE INDICATIONS SENSOR RADIO TROUBLEACTIVATE SENSOR DONE START IN TEST and the sensor status indicator will turn off11.CUSTOMIZING THE SYSTEM MASTER USER CODE 1 GONG & 5 BEEPS SENSORSENSOR NUMBER FOR INTERIOR SENSOR NUMBER FOR CHIME8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONE 7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONEMAKING A SENSOR PERFORM A DIFFERENT FUNCTION SENSOR NUMBER FOR FUNCTION CHANGENEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONE AWAYHOME = PROGRAM SETUP MODE12.ADVANCED PROGRAMMING TEST = REMOVEEXIT DELAY TIME CHANGING A SENSORS RESTORE REQUIREMENTSENTRY DELAY TIME CHANGING A SENSORS SUPERVISIONENTRY DELAY BEEPS REMOTE CONTROL ARMING LEVELREMOTE CONTROL DISARMING LEVEL EXIT DELAY BEEPSDISABLING QUICK ARMING SILENT BURGLARY ALARMSSILENT EMERGENCY ALARMS AUTOMATIC RESTORAL OF BYPASSED SENSORSAUTOMATION OUTPUT ON DURING AND AFTER ALARM AUTOMATION OUTPUT MODE DURING ALARMREMOTE CONTROL ARM/DISARM CHIRP AUTOMATION OUTPUT ON DURING ALARMAUTOMATION OUTPUT WHILE ARMED AUTOMATION OUTPUT DURING EXIT/ENTRY DELAYSREMOTE ACCESS PASSWORD AUTOMATION OUTPUT POLARITYchanged using programming STEP #99 Because access to programming would be impossibleusing these steps. The master user code can be CONSOLE MASTER RESETGeneral Communicator Programming Table SETUP MODE13.COMMUNICATOR PROGRAMMING SETUP MODE2-WAYAUDIO COMMUNICATOR ENABLEGENERAL COMMUNICATOR OPTIONS VOICE RESPONSEDIALING METHOD DIALING DELAYCALL LIMITER HOME PROGRAM 0 FOR NO DELAY 1 FOR 15 SECOND DELAYCALL ROUTING COMMUNICATOR REPORTING OPTIONSREPORTING FORMAT Communicator Reporting Option TablePRIMARY TELEPHONE NUMBER TELEPHONE NUMBER DELAYS AND SPECIAL CHARACTERSACCOUNT NUMBER SECONDARY TELEPHONE NUMBEROPENING AND CLOSING REPORTS REPORT CONSOLE TROUBLEREPORT FORCE ARMING POINT ID REPORTINGSTEPS #201-206 COMMUNICATOR REPORTING CODESGENERAL REPORTING CODES General Reporting Codes TableFORCE ARMING REPORTING CODE SYSTEM REPORTING CODESSTEPS #261-266 DURESS REPORTING CODESTEPS #210-233 4 BY 2 FORMAT POINT ID ALARM REPORT CODES4 BY 2 FORMAT POINT ID REPORTING CODES 4 BY 2 FORMAT POINT ID TROUBLE REPORT CODESSTEP # 4 by 2 Format Point ID Reporting Code Table4 BY 2 FORMAT POINT ID REPORTING CODES PROGRAMMING FUNCTION14. IMPORTANT INFORMATION LINEAR LIMITED WARRANTYWIRELESS PRODUCT NOTICE FCC NOTICE