Rear Panel

Rear Panel

 

1

 

 

2

 

 

 

 

3

4

5

6

 

 

7

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

10 11

 

 

12

 

 

 

 

 

 

 

 

1.

DIN Video Inputs

 

2.

BNC Video Inputs

3.

VGA IN Port

4. Component Video IN

 

 

 

 

 

 

 

 

5.

Component Audio IN

 

6.

Relay / PTZ / RS-232

7.

Ethernet

8. Power (DC 12V)

 

 

 

 

 

 

9.

Audio Inputs

 

10. Spot Out

11. Audio Out

12. Alarm Block

 

 

 

 

 

 

 

 

1.6 PIN DIN VIDEO INPUTS - Channel 1-4 Camera inputs (for cameras with 6 Pin DIN connections).

Cameras with 6 Pin DIN connections draw power from the System - additional

6 PIN DIN

power adapters are not needed.

 

2.BNC VIDEO INPUTS - Channel 1-8 camera inputs (used to connect Cameras with BNC connection type). Cameras with BNC connections require an additional power adaptor.

3.VGA INPUT - Connect a PC (or other devices with a VGA Output) to the System. The System will perform as a Computer Monitor (when in VGA Mode).

4.COMPONENT VIDEO IN - Connect a DVD Player, Set Top Box or Satellite Receiver to the component Video Inputs (Y/Pb/Pr).

5.COMPONENT AUDIO IN - Connect a DVD Player, Set Top Box or Satellite Receiver to the component Audio Inputs (Audio in Left/Right Channels). The Component (Composite) Output must be turned ON on most DVD Players before connection to the System.

6.RELAY / PTZ / RS-232 BLOCK - These terminals are used to send a signal to a secondary device or control PTZ (Pan/Tilt/Zoom) type cameras.

7.ETHERNET PORT - Connects the monitor to a router for connection to the internet. Refer to Appendix #3 for Remote Connection setup.

8.DC INPUT - Connect the AC power using the power cord provided with the unit from the monitor to an electrical outlet

9.RCA AUDIO INPUTS - Channel 1-4 Audio inputs (for BNC type cameras with standard RCA Audio output)

15