Rear View

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

5

 

6

 

 

ON

 

 

 

 

 

 

 

 

 

CAMERA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

 

1

2

3

4

5

6

7

8

 

 

 

9

 

 

 

10

11

12

13

14

15

16

AC IN~

 

OUT

 

 

 

 

 

 

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-240V

 

 

 

OUTPUT A

 

OUTPUT B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

MIC

 

 

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

T T GND GND R R TRM TRM

REMOTE

 

 

 

 

ALARM IN

ADJCLOCK

REC EMERGENCY OUTMODE1

OUTMODE2

OUTMODE3

OUTMODE4

OUTMODE5

OUTCALL

OUTCALLGND

GND 30mAMAX

OUT5VDC

RS-232C

ETHERNET

 

IN

 

 

 

 

 

 

 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

 

 

 

 

 

VIDEO

 

Y/C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SCSI

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-485/ RS-422

RECEIVE SEND

7

8

9

10

11

1. MAIN switch

This is the main power switch. When using this unit, set this switch to ON. Otherwise, the unit cannot be turned ON using the POWER button on the front of the unit.

2. CAMERA OUT connectors

BNC video output connectors. When not is use, the unit provides self internal termination. If needed, a monitor or other device can be connected picking up the input viedo.

3. CAMERA IN connectors

Input viedo connector for camera signal (BNC con- nector).

4. GND terminals

It is the common GND terminal.

5.AUDIO connectors

AUDIO IN connector

Input connector for audio signal (RCA pin).

AUDIO OUT connector

Output connector for audio signal (RCA pin).

6. MIC jack

Input connector for microphone (600 ohm imped- ance). Use of MIC input for audio recording has pri- ority over AUDIO IN connector.

7. AC power socket

This socket connects to the power cord. Earth ter- minal is for safety. Use the 100 ~ 240V plug with earth for the power of this unit.

This unit must be grounded at all times. Never connect this unit to a power outlet which does not have an ground terminal.

Do not connect the earth terminal of a plug to gas pipe, water pipe, lightning rod and so on. The sup-

plied power cord is used for 120V only. Never con- nect to any outlet or power supply having a different voltage or frequency.

12 13 14 15 16

Please use the AC power cord accessory.

8.VIDEO OUT connectors

OUTPUT A VIDEO connector

Output connector for video signal to monitor (BNC connector).

OUTPUT A S(Y/C) connector

Output connector for video signals that separate brightness signals and color signals for higher pic- ture quality. Simultaneous output along with OUT- PUT A VIDEO is also supported.

OUTPUT B connector

Output connector to display live video only (BNC con- nector)( see page 42).

9. RS-485/RS-422 connectors

To connect and operate pan, tilt and zoom cameras.

10. REMOTE jack

Input connector for wired remote (PTZ and unit con- trol).

11. RESET button

Pressing this button resets the unit and the power turns off. Video data, menu settings and the current time are kept.

12.ALARM IN terminals

Input terminal for alarm signal.

13.I/O terminals

CLOCK ADJ terminal

Input terminal to set the present time. Time display is adjusted to the nearest hour (00 minutes 00 seconds) when this terminal receives the CLOCK ADJ signal.

INFORMATION

The on-screen clock can be reset to the nearest hour, by applying a signal to the CLOCK ADJ terminal. For example, if the current time is 11:29:59, it will be reset to 11:00:00, and if the current time is 11:30:00, it will be reset to 12:00:00.

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

Beginning

17

Page 17
Image 17
Mitsubishi Electronics DX-TL2500U Rear View, Main switch, Camera OUT connectors, Camera in connectors, GND terminals