■Data Clear Selection
This unit provides a menu which you can select the data you want to erase.
Example: Clearing the data recorded on main HDD.
1.Display the <MENU SETTING> menu and turn the JOG dial until the cursor( 
) is next to “DATA CLEAR SELECTION”.
USER KEY
@DATA CLEAR SELECTION REAR TERMINAL
2.Turn the SHUTTLE ring to the right to show the <DATA CLEAR SELECTION> menu.
<DATA | CLEAR SELECTION> | |
COPY | DATA CLEAR | OFF |
ARCHIVE DATA CLEAR | OFF | |
@HDD DATA CLEAR | OFF | |
By turning JOG dial, to select the medium of the data clear.
3.Turn the JOG dial until the cursor is next to “HDD DATA CLEAR” and turn the SHUTTLE ring to the right. Turn the JOG dial until “ON” flashes.
•The message, “Turn the SHUTTLE ring >> to EXECUTE.” appears on the screen.
<DATA CLEAR SELECTION>
COPY DATA CLEAR | OFF |
ARCHIVE DATA CLEAR OFF | |
@HDD DATA CLEAR | ON |
| |
“COPY DATA CLEAR” or “ARCHIVE DATA CLEAR” appears on the screen when copy device
or archive device is connected.
4.Turn the SHUTTLE ring to the right to clear the data.
•If not executing, turn the JOG dial until “OFF” flashes and turn the SHUTTLE ring to the right.
Please note that you cannot exit from the menu when clearing the data and “ON” is flashing on the
screen.
5.Turn the SHUTTLE ring to the left or press the SET UP button.
■Rear Terminal Setting (MODE OUT setting)
With this setting, a signal can be output to send the status of this unit.
Example: Setting MODE OUT to “PLAY” (the default setting is “REC”).
1.Display the <MENU SETTING> menu and turn the JOG dial until the cursor is next to “REAR TERMINAL”.
USER KEY
DATA CLEAR SELECTION @REAR TERMINAL
SERVICE
2.Turn the SHUTTLE ring to the right to show the <REAR TERMINAL> menu.
<REAR | TERMINAL> | |
@MODE | OUT | REC |
CAPACITY | REMAIN | |
|
|
|
3.Check the cursor is next to “MODE OUT”, then turn the SHUTTLE ring to the right.
•The
<REAR TERMINAL>
@MODE OUT | REC |
CAPACITY | REMAIN |
4.Turn the JOG dial until “PLAY” flashes and turn the SHUTTLE ring to the right.
•The
<REAR | TERMINAL> | |
@MODE | OUT | PLAY |
CAPACITY | REMAIN | |
|
|
|
By turning the JOG dial, the item of MODE OUT shown on the screen switches as
shown below:
REC
PLAY
POWER
REMAIN
“REC”: The signal is output during recording.
“PLAY”: The signal is output during playback.
“POWER”:The signal is output when the unit’s power switch is on.
“REMAIN”: The signal is output when the remaining storage capacity of main HDD, archive device reaches the rate which is set in CAPACITY REMAIN.
5.Turn the SHUTTLE ring to the left or press the SET UP button.
♦Capacity remain setting
When MODE OUT is set to “REMAIN” and the remaining storage capacity of main HDD or archive device is running out, this unit gives warning. The following shows how to set the device and its remaining capacity ratio to give warn- ing.
When the remaining storage capacity decreases during recording:
•The display of the recorded storage capacity flashes when “DISPLAY MODE 3” is selected.
•The buzzer sounds when BUZZER in the <REAR TERMINAL> menu is set to “REMAIN”.
Example: Setting CAPACITY REMAIN to
1.Display the <MENU SETTING> menu and turn the JOG dial until the cursor is next to “REAR TERMINAL”.
USER KEY
DATA CLEAR SELECTION @REAR TERMINAL
SERVICE
2.Turn the SHUTTLE ring to the right to show the <REAR TERMINAL> menu.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• | •••••••••••• | • |
26