Mitsubishi Electronics DX-TL930E / Various recordings, Alarm Recording (continued) / Various recordings

Alarm Recording (continued) / Various recordings

♦Alarm Recording indicators

1)If the DISPLAY MODE is set for values other than 5 or 6, an Alarm Recordings count will automatically appear on- screen while the unit is running in Alarm Recording mode. (Refer to page 24 for details on DISPLAY MODE.)

2)The Alarm Recording indicator will flash on and off dur- ing Alarm Recording, and will stay on at the completion of Alarm Recording.

If the Alarm recording was made even once, the ALARM REC indicator would keep illuminating.

3)The Alarm Recording counter has a maximum of 9999. When this figure is exceeded, the count will return to 0001.

♦Operation after Alarm Recording

1)At the end of Alarm Recording, the unit will return to the same recording intervals which were in effect before the activation of Alarm Recording.

♦Indexing Alarm Recording time

When the ALARM REC CH. on the <MPX FUNCTIONS> menu is set to” SEP.”, the index signal will be included at the top of the entry for the designated camera with the smallest channel number.

♦Alarm recording cameras

Please refer to “Setting of Alarm recording camera” on page 39 for details.

■Basic recordings

Please refer to “Basic recordings” on page 12 for details.

■Pre-alarm Recording

When the Alarm Recording is in effect, the unit is also able to make recordings of images taken a few seconds before a signal is received by the ALARM IN terminal.

disturbance Alarm input

Time

Camera input

Recording process Records data on HDD before alarm is input.

•Images captured prior to the ALARM IN terminal being triggered will be recorded.

The duration of the Pre-alarm Recording will vary according to the content of the Pre-alarm Record-

ing. The duration of the recording may be lengthened depending on such factors as the recording content and the timing of alarm signal reception.

•When Pre-Alarm Recording has been set, all the cam- eras designated under CAMERA SETTING in the <MPX FUNCTIONS> menu will execute this function. After the alarm is triggered, only the channels using cameras se- lected in the ALARM REC CH. setting will be recorded. Because of this, when the ALARM REC CH. is set to “SEP.”, the number of recording cameras used in pre-alarm and post-alarm recording will differ, and the recording intervals between the two stages will also differ during playback.

INFORMATION

Recording and playback cannot be done when the pre-alarm indicator light is on. In this

case, press the User button to cancel this condition.

The Pre-alarm Recording function can also be used with Timer operation.

1.Set the action in TIMER PROGRAM to POWER.

2.Follow the procedure described in Pre-Alarm recording on page 34 to make necessary settings for pre-alarm recording.

3.Press the TIMER REC button.

•Pre-alarm stand-by mode will start when time is ready.

4.Activate the ALARM IN terminal.

•Pre-alarm Recording will start automatically.

■Repeat Recording

When HDD FULL is selected in the <INITIAL SET UP> menu, it is possible to specify what the unit will do when its memory becomes full. By selecting “REPEAT” in the HDD FULL setting, the unit will continue to record by automatically over-writing the data on its hard disk.

Example: “REPEAT” is selected in the HDD FULL setting.

1.Press the SET UP button to display the <MENU SETTING> menu.

2.Turn the JOG dial to move the cursor ( ) to INITIAL SET UP.

REAR TERMINAL￿ SERVICE￿

@INITIAL SET UP

3.Turn the SHUTTLE ring to the right to display the <INITIAL SET UP > menu.

<INITIAL SET UP>￿
@TIME DATE ADJUST￿	OFF￿
ARCHIVE OVERWRITE￿
HDD FULL￿	STOP￿
HDD PB REPEAT￿	STOP￿
AUTO EJECT￿	ON￿
ARCHIVE DATA	ALL￿
	￿

4.Turn the JOG dial to move the cursor to HDD FULL, then turn the SHUTTLE ring to the right to flash the sub- item.

<INITIAL SET UP>￿
TIME DATE ADJUST￿	OFF￿
ARCHIVE OVERWRITE￿
@HDD FULL￿	STOP￿
HDD PB REPEAT￿	STOP￿
AUTO EJECT￿￿	ON￿
ARCHIVE DATA	ALL

5.Turn the JOG dial till REPEAT appears. Turn the SHUTTLE ring to the right to fix setting.

•The sub-item will stop flashing.

<INITIAL SET UP>￿

TIME DATE ADJUST￿ ARCHIVE OVERWRITE￿ OFF￿

@HDD	FULL￿	REPEAT￿
HDD	PB REPEAT￿	STOP￿
AUTO EJECT￿		ON￿
ARCHIVE DATA		ALL

6.Turn the SHUTTLE ring to the right or press the SET UP button.

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• •••••••••••• •

46