Mitsubishi Electronics WD-73727 manual Receiver Stereo System, To connect an analog A/V receiver

Connecting an A/V Receiver (Stereo System)

Connecting a Satellite Receiver or Other Device with S -Video

A/V Receiver (Stereo System)

Figure 7

Most setups require either a digital audio cable or stereo audio cables. In some circumstances, you may need to connect both digital audio and stereo audio. A digital audio cable is provided with the TV. Stereo audio cables are not included.

Satellite Receiver or Other Device with S-Video

Figure 8

An S-Video cable and audio cables are required. These are not included with the TV.

A.To connect an analog A/V receiver:

Connect a set of stereo audio cables from AUDIO OUTPUT on the TV back panel to the TV AUDIO INPUT on the back of the A/V receiver. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

B.To connect a digital A/V receiver with Dolby® Digital surround sound:

Connect one end of the digital audio cable supplied with the TV to DIGITAL AUDIO on the back of the TV. Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver.

		#
	"7 3FDFJWFS 3FBS 1BOFM
	"
		6TF POMZ JG
		DPOOFDUJOH B
		%PMCZ EJHJUBM
	"	"7 SFDFJWFS
57 #BDL 1BOFM
4FDUJPO	#

Figure 7. Connecting an A/V receiver

On rare occasions, an HDMI signal may be copy- restricted and cannot be output from the TV as a digital signal. To hear these copy-protected signals through the A/V receiver, use connections for analog A/V receivers.

MP3 audio from memory cards cannot be output as digital audio. To listen to MP3 playback from the TV memory card player through your A/V receiver, use the connections for an analog A/V receiver

Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.

1.Connect an S-Video cable from VIDEO OUT on the satellite receiver back panel to INPUT-2 S-VIDEO on the TV back panel.

2.Connect a set of audio cables from AUDIO OUT on the satellite receiver back panel to INPUT-2 AUDIO on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

Note: Refer to the Satellite Receiver Owner’s Guide for Dish Antenna connections

						"OZ 47JEFP %FWJDF
		8IJUF				"6%*0 065		"6%*0 */	7*%&0 065
						-		-	:$
							
						3		3
		3FE
									
		
							57 CBDL QBOFM TFDUJPO
8IJUF				COMPONENT
		INPUT	1	YPbPr (480i/480p/720p/1080i)2		
		1	2				Y		INPUT	OUTPUT
									DVI
										AUDIO	RECORD
		S-VIDEO						Analog Audio		OUTPUT	OUTPUT
							Pb	1	2
											VIDEO
3FE		VIDEO					Pr				AUDIO-
											LEFT/
							AUDIO-				(MONO)
		AUDIO-
		LEFT/					LEFT/
		(MONO)					(MONO)				AUDIO-
											RIGHT
		AUDIO-					AUDIO-
		RIGHT					RIGHT
								MONITORLINK™/HDMI		PC - 60Hz
								VIDEO 480i/480p/720p/1080i		VGA, W-VGA,
								AUDIO PCM LINEAR		SVGA, W-SVGA,
								1	2	XGA, 1280 X 720
		',INK¸
			IR EMITTER
			Net Command¸
		DTV/CABLE/
		VHF/UHF
					DIGITAL
			ANT 1 / MAIN	ANT 2 / AUX	AUDIO		CableCARD™ USE WITH ANT 1 CARD TOP
					OUTPUT
											IEEE 1394
											INPUT/
											OUTPUT

Figure 8. Connecting a Satellite Receiver with S-Video

Note: NetCommand® assumes you connected your satellite receiver to Input-2. If you add a second satellite receiver or use any other inputs for your satellite receiver, this change must match in the NetCommand system. See Editing NetCommand Setup in Chapter 3 for more information.

28Chapter 2. Connecting