Mitsubishi Electronics WD-52628, WD-73727, WD-62628 Connecting a VCR to a Cable Box Audio & Video

Connecting a VCR to a Cable Box (Audio & Video)

VCR to a Cable Box (Audio & Video)

Figure 6

A two-way RF splitter, 4 coaxial cables, right and left audio cables and an S-Video or Video cable are required. These are not included with the TV but are available at most electronics stores.

1.Connect the incoming cable to IN on the RF splitter.

2.Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the cable box back panel.

3.Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. This connection also allows you to use the TV Guide On Screen® feature.

4.Connect one coaxial cable from OUT on the cable box to ANTENNA IN on the VCR back panel.

5.Connect one coaxial cable from ANTENNA OUT on the VCR back panel to ANT-2 AUX on the TV back panel (optional).

6.To use the TV speakers with the VCR, connect a set of audio cables from AUDIO OUT on the VCR back panel to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable

connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable.

7.Connect either an S-Video or composite video cable from VIDEO OUT on the VCR back panel to INPUT 1 VIDEO on the TV back panel. Connect only one type of video cable. S-Video is recommended, if available.

8.For NetCommand®-controlled recordings (including TV Guide On Screen)

a.Connect a set of audio cables from AUDIO IN on the VCR back panel to RECORD OUTPUT/AUDIO- LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

b.Connect a video cable from VIDEO IN on the VCR back panel to RECORD OUTPUT/VIDEO on the TV back panel.

Note: With this connection configuration, it is possible to view live cable programs through the VCR. For best picture quality, however, always view live cable programs directly from the cable box instead of the VCR.



B

*G ZPVS 7$3 IBT B

7$3 CBDL QBOFM

WJEFP DIBOOFM PS 3'

0/0'' TXJUDI TFU JU



UP 0''

)46



"UUBDI POMZ POF WJEFP



C

DBCMF UZQF TUFQ  

4WJEFP SFDPNNFOEFE

JG BWBJMBCMF



INPUT

1

YPbPr (480i/480p/720p/1080i)2



COMPONENT

1

2

Y

INPUT

OUTPUT

C

DVI

AUDIO

RECORD

S-VIDEO

Analog Audio

OUTPUT

OUTPUT

Pb

1

2

VIDEO

VIDEO

Pr

AUDIO-

LEFT/

AUDIO-

(MONO)

AUDIO-

LEFT/

LEFT/

AUDIO-

3' 4QMJUUFS

(MONO)

(MONO)

RIGHT

RIGHT

RIGHT



AUDIO-

AUDIO-

B



1

2

PC - 60Hz

MONITORLINK™/HDMI

VIDEO 480i/480p/720p/1080i

VGA, W-VGA,

AUDIO PCM LINEAR

SVGA, W-SVGA,



XGA, 1280 X 720

-*55&3

065

',INK¸

*/ 580 8": 41

065

Net Command¸

*ODPNJOH

IR EMITTER



$BCMF

		DTV/CABLE/
		VHF/UHF
				DIGITAL
				AUDIO	CableCARD™ USE WITH ANT 1 CARD TOP
		ANT 1 / MAIN	ANT 2 / AUX	OUTPUT
					IEEE 1394
					INPUT/
					OUTPUT
*/			

065

$BCMF
#PY 

CBDL
QBOFM
TFDUJPO

Figure 6. Connecting a VCR to a Cable Box

Note: NetCommand® will assume your VCR is connected to inputs as shown on this page. If you use any other inputs for your VCR or add a second VCR, this change must match

in the NetCommand system. See Edit NetCommand... in Chapter 3 for more information.

Chapter 2. Connecting 27