MVME197LE Module Installation | Motorola specification

	Installation Instructions
	MVME197LE Module Installation	2
	Now that the MVME197LE module is ready for installation, proceed as	2

	follows:

a.Turn all equipment power OFF and disconnect the power cable from the power source.

Caution

!

WARNING

Inserting or removing modules while power is applied could result in damage to module components.

DANGEROUS VOLTAGES, CAPABLE OF CAUSING DEATH, ARE PRESENT IN THIS EQUIPMENT. USE EXTREME CAUTION WHEN HANDLING, TESTING, AND ADJUSTING.

b.Remove the chassis cover as instructed in the equipment user’s manual.

c.Remove the filler panel(s) from the appropriate card slot(s) at the front and rear of the chassis (if the chassis has a rear card cage). The MVME197LE module requires power from both P1 and P2. It may be installed in any double-height unused card slot, if it is not configured as the system controller. If the MVME197LE is configured as the system controller, it must be installed in the left-most card slot (slot 1) to correctly initiate the bus-grant daisy-chain and to have proper operation of the IACK-daisy- chain driver. The MVME197LE is to be installed in the front of the chassis and the MVME712X transition board which has a double-wide front panel is to be installed in the rear of the chassis.

d.Carefully slide the MVME197LE module into the card slot. Be sure the module is seated properly into the P1 and P2 connectors on the backplane. Do not damage or bend connector pins. Fasten the module in the chassis with screws provided, making good contact with the transverse mounting rails to minimize RFI emissions.

e.Remove the IACK and BG jumpers from the header on the chassis backplane for the card slot in which the MVME197LE is installed.

f.Connect the P2 Adapter Board and specified cable(s) to the MVME197LE at P2 on the backplane at the MVME197LE slot, to mate with (optional) terminals or other peripherals at the EIA-232-D serial ports, parallel port, SCSI ports, and LAN Ethernet port. Refer to the manuals listed in the Related Documentation section for information on installing the P2 Adapter Board and the MVME712X transition module. (Some connection diagrams

MVME197LE/D2

2-7

Image 27

Motorola user manual MVME197LE Module Installation

Contents

MVME197LE/D2 MVME197LE Restricted Rights Legend Document Terminology Preface BIT Document Title Motorola Publication Number Related DocumentationPage Page Safety Summary Safety Depends on YOU Contents Appendix a List of Figures Xii List of Tables Xiv General Description Introduction Ote Features Specifications MVME197LE SpecificationsCharacteristics Specifications Cooling Requirements FCC Compliance Equipment Required Support Information Hardware Preparation Unpacking Instructions Hardware Preparation and Installation VMEbus Connector P1 Configuration Switches Switch S1Configuration Switch S1 General Information S1-1 to S1-8 OFF -- All Ones Factory Configuration Installation Instructions Switch S6Connectors MVME197LE Module Installation System Considerations MVME197LE/D2 Hardware Preparation and Installation Controls and Indicators Abort Switch S2Reset Switch S3 Front Panel Indicators DS1-DS6 Memory MapsProcessor Bus Memory Map Processor Bus Memory Map Local Devices Memory Map Address Range Devices Accessed Port Size Detailed I/O Memory Maps 110 BusSwitch Register Memory Map100 108 Memory Maps ECDM0 ECDM1 ECDM2 ECDM3 ADDR/REGISTER Ecdm CSR Register Memory Map Dcam I2C Register Memory Map Dcam I2C Base Address = $C0 default Offset Operating Instructions Offset VMEchip2 Memory Map Sheet 1 Operating Instructions VMEchip2 Memory Map Sheet 2 Global Access BUS Watchdog Timeout Prescaler Adjust Operating Instructions VMEchip2 Memory Map Sheet 3 Operating Instructions VMEchip2 Gcsr Base Address = $FFF40100 VMEchip2 Memory Map Sheet 4 Operating Instructions PCCchip2 Memory Map Printer Busy Interrupt Control Register $FFF42034 Printer Fault Interrupt Control Register $FFF42031Printer SEL Interrupt Control Register $FFF42032 Printer PE Interrupt Control Register $FFF42033 Cirrus Logic CD2400 Memory Map Offsets Size Access Cirrus Logic CD2401 Serial Port Memory MapBase Address Is $FFF45000 Data Bits Address D31 D16 D15 Address Range Description Size Bytes Accesses may be 8-bit or 32-bit, but not 16-bit11 C710 Scsi Memory Map 12. MK48T08 BBRAM, TOD Clock Memory Map 13. Bbram Configuration Area Memory Map 14. TOD Clock Memory MapData Bits Address Function BBRAM, TOD Clock Memory Map 0460000000470476 5000 VMEbus Accesses to the Local Peripheral BusVMEbus Memory Map 01-W3869B03A Local Reset Operation Software InitializationMulti-MPU Programming Considerations User’s Manual MVME197LE Functional Description Data Bus StructureMC88110 MPU Functional Description Memory Array Bus Data Bus 256 BusSwitchMC88110 Address Data MUX Address Mezzanine Address Bus Battery Backup RAM and Clock Flash MemoryOnboard Dram VMEbus Interface InterfacesSerial Port Interface Ethernet Interface Printer Interface Scsi Termination Programmable Tick TimersPeripheral Resources Scsi Interface Interrupt Sources Watchdog TimerProcessor Bus Timeout Local Peripheral Bus Timeout MVME197LE/D2 Functional Description EIA-232-D Interconnections Table A-1. EIA-232-D Interconnections Pin Signal Signal Name and Description Number Mnemonic Ring Indicator RI is sent by the modem to User’s Manual Figure A-1. Middle-of-the-Road EIA-232-D Configuration Figure A-2. Minimum EIA-232-D Connection Numerics Index IN-2 IN-3 Index