Left side of the saw has a right-hand thread | Multiquip SP303526

MQ SP-3035 CONCRETE SAW

Installing the Blade, Blade Guard & Blade Flange

WARNING

Remain Clear of all parts of saw while installing blade to prevent crush injury or death.

Verify the engine start switch is OFF before installing blade.

Tighten the 5/8” blade-mounting bolt to 100-125 foot- pounds torque.

The blade can be mounted on either side of the saw to accommodate different cutting jobs.

1.Raise the saw so that the blade will clear the ground when installed.

2.Verify that blade flanges are clean and undamaged.

3.Insert the bushing and mounting bolt through the outer flange and blade.

4.Align flange pin through the blade into the inner flange.

5.Tighten the 5/8” mounting bolt to 100-125foot-poundsof torque.


	The blade mounting bolt on the right side of the saw (as viewed from the
	operator’s position) has a left hand-thread, while the blade-mounting bolt on
NOTE	the left side of the saw has a right-hand thread.
NOTE

Outer Flange with Pin

Blade Guard

FlangeMounting Clip

Bushing

Inner Flange

Tapered

MountingSpindle Shaft

Bolt

Fig. 6 — Blade Components

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 20

Image 22

Multiquip SP303526 manual Installing the Blade, Blade Guard & Blade Flange, Left side of the saw has a right-hand thread

Contents

SP3 Street PRO Professional Slab SAW Page Proposition 65 Warning Silicosis /RESPIRATORY Hazards Table of Contents MQ SP-3035 Concrete SAW 119 Parts Ordering Procedures Safety Hazard Symbols Crush and Pinch Hazard Keep hands and feet clear Equipment Damage Message General Safety Warnings General Safety Warnings Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Serial Tag Model no SPEC. no Serial no Operation Before Starting Control Panel Control Panel Engine Power, Cutting Power & Sheave Size Blade Size & Configuration per Model Installing the Blade, Blade Guard & Blade Flange Left side of the saw has a right-hand thread Removing the Blade, Blade Guard & Blade Flange Blade Guard Removal Stacking Blades for Wide Cuts Blade Stacking Installing and Removing the Blade Guard Installing the Blade Guard Removing the Blade Guard Installing the Flange Guard Flange Guard, Installed Water Supply and Control Water Supply System Handlebars Handlebar Positions Fueling the Saw Use 90+ Octane Unleaded Gasoline Only ON/OFF Switch Location Starting and Stopping the Engine Pointer Adjustment Pointer Adjustment Raise Lower Controls Joystick Handle Setting the Depth Gauge Setting the Depth Gauge & Depth StopSetting the Depth Stop Drive System Drive System Drive System Controls Do not Disengage While Engine is Running Positraction Positraction System Night Light Transaxle Tie-downs Transportation Tie-downs and Lift PointLift Point Operation on a Slope or Incline Using Inclined Ramps to Load and Unload the SawFreeing a Stuck Blade Draining the Water System Maintenance Removable Guards and Access Panels Belts and Pulleys Belt Tension Spindle Blade Shaft Drive Belt Tension Adjustment Detail of Engine Mount Lock Bolts Spindle Drive Belt Adjustment & Replacement Replacing the Spindle Drive Belt Replacing the Jack Shaft Belt Rotary Belt Tensioner Blade Flange Removal/Installation Removing the Inner Blade Flange Installing the Inner Blade Flange Installing the Inner Spindle For Spindle Maintenance/hydraulic oil change see Spindle Replacement Engine Mount Lock Bolts Saddle Maximum Cut Depth Adjustment Circuit Breakers Lubrication Grease Fittings and Maximum Cut Depth Stops Engine Maintenance Filters Raise-Lower System Raise-Lower System Control Handle Adjustment Control Handle Adjustment Routine Maintenance Hydraulic System Draining & Filling the Hydraulic System To drain the Transaxle To refill the hydraulic system Drive Wheel Alignment Drive Wheel Alignment Pivot Side Adjustment Side Attachment Bolts Positraction Adjustment Positraction Adjustment Bolt Locations Explanation of Code in Remarks Column To 3 Units Component Drawings Nameplate and Decals Assy DECAL, MQ Diamond Logo DECAL, WARNING, Keep Feet ClearDECAL, Blade Guard Removal DECAL, SP3 Logo Deck/Gauge Panel Assy Gauge Panel Deck Panel Console/Sheet Metal Assy CONSOLE, RED WASHER, Flat SAE 3/8 GRD 9 YZBelt Guard HARNESS, Light KIT, Socket Access Panel Assy PANEL, Rear CONSOLE, RED LATCH, Rear SAW Access PanelDocument BOX, CP90007-07 Fuel Tank Assy VALVE, Fuel ON/OFF 1/4 TANK, FuelBUSHING, Rubber Fuel Dapco CLAMP, Hose Worm #2 R Control Handle Assy Switch Assembly Rubber BootPLATE, Side Switch Handle Housing Joystick Mounting Assy SPACER, F-N-R BOOT, FNR Control HandleWASHER, FLAT, #10 BELLCRANK, SAW F-N-R Lift Pump Circuit Assy CYLINDER, Lift PUMP, LiftPIN, Cylinder FITTING, 45 4MJ-4MO Water System Assy HOSE, 1/2 ID Pushlock 250 PSI VALVE, BALL, 1/2 BrassFITTING, Brass 8 PUSH-ON 1/2 MP Depth Indicator Assy AXLE, Indicator Sheave Depth Indicator U-BRACKETDepth Indicator Cable POINTER, Depth Handle and Light Assy Light BAR, Concrete SAW CONNECTOR, PLUG, 4 PIN FemaleNUT, Nylock WASHER, Lock 5/16 Front/Rear Pointer Assy Rope ASSY., Front Pointer Right Side PointerLeft Side Pointer POINTER, Front 17-1/4 Gauges and Controls Assy HARNESS, Wiring SWITCH, IgnitionSWITCH, Rocker Cable Pull Front Axle Assy BEARING, Flanged WASHER, Flat SAE 7/16Bearing Backing Plate SCREW, SQHS, CP Depth Stop Assy SPRING, COMPRESSION, 7/8 Depth Stop Lead ScrewWASHER, Flat SAE 1/2 COLLAR, SET .50 ID Platform Assy SPACER, Bladeguard CLIP, .25 Thick PlatformCLIP, MOUNT,BLADEGUARD WASHER, Lower Belt Protector Drive Assy Part Name QTY Remark Bladeshaft and Mounting Assy CONNECTOR, Weatherpack 2 Male PIN HOUSING, Single Speed W/TACHGENERATOR, Tachometer Signal Mounting BLOCK, Bladeshaft Positraction Assy COVER, Handle Flat RED Lever ConnectorPositraction Actuator Lever WASHER, Bellview 1/2 X 1-1/4 Pulley and V-Belt Assy MQ SP-3035 Concrete Saw Pulley and V-Belt Assy Battery Assy CABLE, Battery POS 4 GA X 48 Post TBD BATTERY, Group 26RMOUNT, Battery Clamp CABLE, 24 POS TBD CABLE, Battery NEG Engine Brackets Assy Lifting Ring AIR Filter HOUSING, ASMFILTER, AIR, ELEMENT,SAFETY STANDOFF, Lifting Plate 35HP Engine Installation Assy WASHER, Flat SAE 5/8 GRD 9 YZ MOUNT, Jackshaft Pivot ARMMOUNT, Motor Tensioner NUT, HEX Finish 5/8-11 Bladeguard Assy Blade Guard 26-INCH Blade Guard 16-INCHBlade Guard 20-INCH Blade Guard 30-INCH Optional Water Pump Kit Assy PUMP, Water Jabsco DescriptionMOUNT, Water Pump FITTING, Brass 1/2FP-1MP Collar Puller Assy PLATE, Puller Outer PullerCollar Puller Instruction Sheet Seal Sleeve Puller/Seal Installation Tool SCREW, 10 24 X 12 Full Thread Seal Installation ToolSCREW, 10 24 X 6 Full Thread TOOL, Seal Removal Bushing Extension Kits Bushing Extension KIT 18501 .375 Electric Schematic Specifications Heres HOW to GET Help