Blade Flange Removal/Installation | Multiquip SP303520, SP303516

MQ SP-3035 CONCRETE SAW

Blade Flange Removal/Installation

Correct removal or installation of the Inner Blade Flange or Flange requires a Flange Puller (option Part Number 18503) as shown below.

WARNING

Follow instructions closely to prevent injury from flying Blade Flanges!

Because of tapered fit between Blade Flange and Spindle, 5-10 tons of force is needed to release the inner flange. Parts and tools can become dangerous projectiles if instructions are not followed properly.

Front Puller Plate

Perimeter Bolt

Horseshoe Plate

Puller Bolt

Perimeter Bolt

Perimeter Bolt

Fig. 31 — Using the Flange Puller

Removing the Inner Blade Flange

With the Outer Blade Flange in place, and the Blade Mounting Bolt loosened approximately ¼”:

1.With the three perimeter bolts holding the two Puller Plates together, slide the Horseshoe Plate of the Flange Puller behind the (Shaft) side of the Inner Flange as shown above.

2.Tighten the center Puller bolt to remove the Inner Flange from Spindle.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 45

Image 47

Multiquip SP303520, SP303516, SP303530, SP303526 manual Blade Flange Removal/Installation, Removing the Inner Blade Flange

Contents

SP3 Street PRO Professional Slab SAW Page Proposition 65 Warning Silicosis /RESPIRATORY Hazards Table of Contents MQ SP-3035 Concrete SAW 119 Parts Ordering Procedures Safety Hazard Symbols Crush and Pinch Hazard Keep hands and feet clear Equipment Damage Message General Safety Warnings General Safety Warnings Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Model no SPEC. no Serial no Serial Tag Before Starting Operation Control Panel Control Panel Blade Size & Configuration per Model Engine Power, Cutting Power & Sheave Size Left side of the saw has a right-hand thread Installing the Blade, Blade Guard & Blade Flange Blade Guard Removal Removing the Blade, Blade Guard & Blade Flange Blade Stacking Stacking Blades for Wide Cuts Installing the Blade Guard Installing and Removing the Blade Guard Removing the Blade Guard Flange Guard, Installed Installing the Flange Guard Water Supply System Water Supply and Control Handlebar Positions Handlebars Use 90+ Octane Unleaded Gasoline Only Fueling the Saw Starting and Stopping the Engine ON/OFF Switch Location Pointer Adjustment Pointer Adjustment Joystick Handle Raise Lower Controls Setting the Depth Stop Setting the Depth Gauge & Depth StopSetting the Depth Gauge Drive System Drive System Do not Disengage While Engine is Running Drive System Controls Positraction System Positraction Transaxle Night Light Lift Point Transportation Tie-downs and Lift PointTie-downs Freeing a Stuck Blade Using Inclined Ramps to Load and Unload the SawOperation on a Slope or Incline Draining the Water System Removable Guards and Access Panels Maintenance Belt Tension Belts and Pulleys Detail of Engine Mount Lock Bolts Spindle Blade Shaft Drive Belt Tension Adjustment Replacing the Spindle Drive Belt Spindle Drive Belt Adjustment & Replacement Rotary Belt Tensioner Replacing the Jack Shaft Belt Removing the Inner Blade Flange Blade Flange Removal/Installation Installing the Inner Spindle Installing the Inner Blade Flange For Spindle Maintenance/hydraulic oil change see Engine Mount Lock Bolts Spindle Replacement Saddle Circuit Breakers Maximum Cut Depth Adjustment Grease Fittings and Maximum Cut Depth Stops Lubrication Filters Engine Maintenance Raise-Lower System Raise-Lower System Control Handle Adjustment Control Handle Adjustment Hydraulic System Routine Maintenance To drain the Transaxle Draining & Filling the Hydraulic System To refill the hydraulic system Drive Wheel Alignment Drive Wheel Alignment Pivot Side Adjustment Side Attachment Bolts Positraction Adjustment Bolt Locations Positraction Adjustment Explanation of Code in Remarks Column To 3 Units Nameplate and Decals Assy Component Drawings DECAL, SP3 Logo DECAL, WARNING, Keep Feet ClearDECAL, Blade Guard Removal DECAL, MQ Diamond Logo Deck/Gauge Panel Assy Deck Panel Gauge Panel Console/Sheet Metal Assy HARNESS, Light KIT, Socket WASHER, Flat SAE 3/8 GRD 9 YZBelt Guard CONSOLE, RED Access Panel Assy Document BOX, CP90007-07 LATCH, Rear SAW Access PanelPANEL, Rear CONSOLE, RED Fuel Tank Assy CLAMP, Hose Worm #2 TANK, FuelBUSHING, Rubber Fuel Dapco VALVE, Fuel ON/OFF 1/4 R Control Handle Assy Handle Housing Rubber BootPLATE, Side Switch Switch Assembly Joystick Mounting Assy BELLCRANK, SAW F-N-R BOOT, FNR Control HandleWASHER, FLAT, #10 SPACER, F-N-R Lift Pump Circuit Assy FITTING, 45 4MJ-4MO PUMP, LiftPIN, Cylinder CYLINDER, Lift Water System Assy FITTING, Brass 8 PUSH-ON 1/2 MP VALVE, BALL, 1/2 BrassHOSE, 1/2 ID Pushlock 250 PSI Depth Indicator Assy POINTER, Depth Depth Indicator U-BRACKETDepth Indicator Cable AXLE, Indicator Sheave Handle and Light Assy WASHER, Lock 5/16 CONNECTOR, PLUG, 4 PIN FemaleNUT, Nylock Light BAR, Concrete SAW Front/Rear Pointer Assy POINTER, Front 17-1/4 Right Side PointerLeft Side Pointer Rope ASSY., Front Pointer Gauges and Controls Assy Cable Pull SWITCH, IgnitionSWITCH, Rocker HARNESS, Wiring Front Axle Assy SCREW, SQHS, CP WASHER, Flat SAE 7/16Bearing Backing Plate BEARING, Flanged Depth Stop Assy COLLAR, SET .50 ID Depth Stop Lead ScrewWASHER, Flat SAE 1/2 SPRING, COMPRESSION, 7/8 Platform Assy WASHER, Lower Belt Protector PlatformCLIP, MOUNT,BLADEGUARD SPACER, Bladeguard CLIP, .25 Thick Drive Assy Part Name QTY Remark Bladeshaft and Mounting Assy Mounting BLOCK, Bladeshaft HOUSING, Single Speed W/TACHGENERATOR, Tachometer Signal CONNECTOR, Weatherpack 2 Male PIN Positraction Assy WASHER, Bellview 1/2 X 1-1/4 Lever ConnectorPositraction Actuator Lever COVER, Handle Flat RED Pulley and V-Belt Assy MQ SP-3035 Concrete Saw Pulley and V-Belt Assy Battery Assy CABLE, 24 POS TBD CABLE, Battery NEG BATTERY, Group 26RMOUNT, Battery Clamp CABLE, Battery POS 4 GA X 48 Post TBD Engine Brackets Assy STANDOFF, Lifting Plate 35HP AIR Filter HOUSING, ASMFILTER, AIR, ELEMENT,SAFETY Lifting Ring Engine Installation Assy NUT, HEX Finish 5/8-11 MOUNT, Jackshaft Pivot ARMMOUNT, Motor Tensioner WASHER, Flat SAE 5/8 GRD 9 YZ Bladeguard Assy Blade Guard 30-INCH Blade Guard 16-INCHBlade Guard 20-INCH Blade Guard 26-INCH Optional Water Pump Kit Assy FITTING, Brass 1/2FP-1MP DescriptionMOUNT, Water Pump PUMP, Water Jabsco Collar Puller Assy Collar Puller Instruction Sheet Outer PullerPLATE, Puller Seal Sleeve Puller/Seal Installation Tool TOOL, Seal Removal Seal Installation ToolSCREW, 10 24 X 6 Full Thread SCREW, 10 24 X 12 Full Thread Bushing Extension Kits Bushing Extension KIT 18501 .375 Electric Schematic Specifications Heres HOW to GET Help