Safety | Multiquip SP303530, SP303516, SP303526, SP303520 guide

MQ SP-3035 CONCRETE SAW

SAFETY

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been developed to provide instructions for the safe and efficient operation of the Multiquip SP-3035 CONCRETE SAW.

NOTE For engine maintenance information, please refer to the engine manufacturers’ instructions for data relative to its safe operation.

Before using this CONCRETE SAW, ensure that the operating individual has read and understands all instructions in this manual.

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.

DANGER: You WILL be KILLED or SERIOUSLY injured if you

DO NOT follow directions.

DANGER

WARNING: You CAN be KILLED or SERIOUSLY injured if you

DO NOT follow directions.

WARNING

CAUTION: You CAN be injured if you DO NOT follow directions.

CAUTION

Potential hazards associated with SP-3035 Concrete Saw operation will be referenced with "Hazard Symbols" which appear throughout this manual, and will be referenced in conjunction with Safety "Message Alert Symbols".

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 7

Image 9

Multiquip SP303530, SP303516, SP303526, SP303520 manual Safety

Contents

SP3 Street PRO Professional Slab SAW Page Proposition 65 Warning Silicosis /RESPIRATORY Hazards Table of Contents MQ SP-3035 Concrete SAW 119 Parts Ordering Procedures Safety Hazard Symbols Crush and Pinch Hazard Keep hands and feet clear Equipment Damage Message General Safety Warnings General Safety Warnings Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Model no SPEC. no Serial no Serial Tag Before Starting Operation Control Panel Control Panel Blade Size & Configuration per Model Engine Power, Cutting Power & Sheave Size Left side of the saw has a right-hand thread Installing the Blade, Blade Guard & Blade Flange Blade Guard Removal Removing the Blade, Blade Guard & Blade Flange Blade Stacking Stacking Blades for Wide Cuts Installing the Blade Guard Installing and Removing the Blade Guard Removing the Blade Guard Flange Guard, Installed Installing the Flange Guard Water Supply System Water Supply and Control Handlebar Positions Handlebars Use 90+ Octane Unleaded Gasoline Only Fueling the Saw Starting and Stopping the Engine ON/OFF Switch Location Pointer Adjustment Pointer Adjustment Joystick Handle Raise Lower Controls Setting the Depth Gauge & Depth Stop Setting the Depth GaugeSetting the Depth Stop Drive System Drive System Do not Disengage While Engine is Running Drive System Controls Positraction System Positraction Transaxle Night Light Transportation Tie-downs and Lift Point Tie-downsLift Point Using Inclined Ramps to Load and Unload the Saw Operation on a Slope or InclineFreeing a Stuck Blade Draining the Water System Removable Guards and Access Panels Maintenance Belt Tension Belts and Pulleys Detail of Engine Mount Lock Bolts Spindle Blade Shaft Drive Belt Tension Adjustment Replacing the Spindle Drive Belt Spindle Drive Belt Adjustment & Replacement Rotary Belt Tensioner Replacing the Jack Shaft Belt Removing the Inner Blade Flange Blade Flange Removal/Installation Installing the Inner Spindle Installing the Inner Blade Flange For Spindle Maintenance/hydraulic oil change see Engine Mount Lock Bolts Spindle Replacement Saddle Circuit Breakers Maximum Cut Depth Adjustment Grease Fittings and Maximum Cut Depth Stops Lubrication Filters Engine Maintenance Raise-Lower System Raise-Lower System Control Handle Adjustment Control Handle Adjustment Hydraulic System Routine Maintenance To drain the Transaxle Draining & Filling the Hydraulic System To refill the hydraulic system Drive Wheel Alignment Drive Wheel Alignment Pivot Side Adjustment Side Attachment Bolts Positraction Adjustment Bolt Locations Positraction Adjustment Explanation of Code in Remarks Column To 3 Units Nameplate and Decals Assy Component Drawings DECAL, Blade Guard Removal DECAL, WARNING, Keep Feet ClearDECAL, MQ Diamond Logo DECAL, SP3 Logo Deck/Gauge Panel Assy Deck Panel Gauge Panel Console/Sheet Metal Assy Belt Guard WASHER, Flat SAE 3/8 GRD 9 YZCONSOLE, RED HARNESS, Light KIT, Socket Access Panel Assy LATCH, Rear SAW Access Panel PANEL, Rear CONSOLE, REDDocument BOX, CP90007-07 Fuel Tank Assy BUSHING, Rubber Fuel Dapco TANK, FuelVALVE, Fuel ON/OFF 1/4 CLAMP, Hose Worm #2 R Control Handle Assy PLATE, Side Switch Rubber BootSwitch Assembly Handle Housing Joystick Mounting Assy WASHER, FLAT, #10 BOOT, FNR Control HandleSPACER, F-N-R BELLCRANK, SAW F-N-R Lift Pump Circuit Assy PIN, Cylinder PUMP, LiftCYLINDER, Lift FITTING, 45 4MJ-4MO Water System Assy VALVE, BALL, 1/2 Brass HOSE, 1/2 ID Pushlock 250 PSIFITTING, Brass 8 PUSH-ON 1/2 MP Depth Indicator Assy Depth Indicator Cable Depth Indicator U-BRACKETAXLE, Indicator Sheave POINTER, Depth Handle and Light Assy NUT, Nylock CONNECTOR, PLUG, 4 PIN FemaleLight BAR, Concrete SAW WASHER, Lock 5/16 Front/Rear Pointer Assy Left Side Pointer Right Side PointerRope ASSY., Front Pointer POINTER, Front 17-1/4 Gauges and Controls Assy SWITCH, Rocker SWITCH, IgnitionHARNESS, Wiring Cable Pull Front Axle Assy Bearing Backing Plate WASHER, Flat SAE 7/16BEARING, Flanged SCREW, SQHS, CP Depth Stop Assy WASHER, Flat SAE 1/2 Depth Stop Lead ScrewSPRING, COMPRESSION, 7/8 COLLAR, SET .50 ID Platform Assy CLIP, MOUNT,BLADEGUARD PlatformSPACER, Bladeguard CLIP, .25 Thick WASHER, Lower Belt Protector Drive Assy Part Name QTY Remark Bladeshaft and Mounting Assy GENERATOR, Tachometer Signal HOUSING, Single Speed W/TACHCONNECTOR, Weatherpack 2 Male PIN Mounting BLOCK, Bladeshaft Positraction Assy Positraction Actuator Lever Lever ConnectorCOVER, Handle Flat RED WASHER, Bellview 1/2 X 1-1/4 Pulley and V-Belt Assy MQ SP-3035 Concrete Saw Pulley and V-Belt Assy Battery Assy MOUNT, Battery Clamp BATTERY, Group 26RCABLE, Battery POS 4 GA X 48 Post TBD CABLE, 24 POS TBD CABLE, Battery NEG Engine Brackets Assy FILTER, AIR, ELEMENT,SAFETY AIR Filter HOUSING, ASMLifting Ring STANDOFF, Lifting Plate 35HP Engine Installation Assy MOUNT, Motor Tensioner MOUNT, Jackshaft Pivot ARMWASHER, Flat SAE 5/8 GRD 9 YZ NUT, HEX Finish 5/8-11 Bladeguard Assy Blade Guard 20-INCH Blade Guard 16-INCHBlade Guard 26-INCH Blade Guard 30-INCH Optional Water Pump Kit Assy MOUNT, Water Pump DescriptionPUMP, Water Jabsco FITTING, Brass 1/2FP-1MP Collar Puller Assy Outer Puller PLATE, PullerCollar Puller Instruction Sheet Seal Sleeve Puller/Seal Installation Tool SCREW, 10 24 X 6 Full Thread Seal Installation ToolSCREW, 10 24 X 12 Full Thread TOOL, Seal Removal Bushing Extension Kits Bushing Extension KIT 18501 .375 Electric Schematic Specifications Heres HOW to GET Help