Setup Procedure, Connect the equipment | NEC 50PD1, 42PD2 manual

Setup Procedure

1.Determine the installation location

*To ensure safe use, see “Before Use” and “Observe the Following,” then install properly.

2.Connect the equipment

Set the termination switch (75Ω/high impedance). Set the DIP switches to suit the application and system structure. (See Page 17.)

(Loop-out connections are for one unit, maximum.)

3.Install the remote control batteries.

*To use the remote control in the wired arrangement, connect the supplied remote control cable.

4.Connect the supplied power cable

*The maximum current rating 5.6(A) : 42PD2

*The maximum current rating 7.4(A) : 50PD1

5.Switch on the power of each of the devices

*When connected with a computer, switch on the power of the computer first.

6.Input an analog RGB signal or a video signal to this unit

7.Select the input mode

*Select the appropriate RGB input or video input.

8.Adjust the screen

*Make adjustments when adjustment of the screen display position or distortion is required.

9.Adjust the image

*Make adjustments when adjustment of the tint, brightness, or contrast is required.

Warning

For proper installation and mounting it is strongly recom- mended to use a trained, authorized NEC dealer.

Failure to follow correct mounting procedures could re- sult in damage to the unit or injury to the installer. Product warranty does not cover damage caused by im- proper installation.

Notice:

This monitor requires the use of a tabletop stand or wall mount unit for permanent installation and use.

This monitor cannot be used without one of these accesso- ries.

Note:

RETRACTABLE FEET ARE FOR TEMPORARY USE ONLY AND ARE NOT INTENDED FOR PERMA- NENT INSTALLATION.

MODEL # PX-42VPU1-ST STAND IS REQUIRED FOR PERMANENT TABLETOP INSTALLATION. REPLACE THE FEET WHEN YOU MOVE THE MONITOR.

10

Image 10

NEC 50PD1, 42PD2, 42PD2, 50PD1 user manual Setup Procedure, Connect the equipment

Contents

User’s Manual Precautions Important Information To avoid damage and prolong operating life DOC avis de conformation PrécautionsMises en garde et précautions de sécurité Remarque Limited Warranty Plasma Monitors What is Covered and What is not Covered Contents Ventilation Requirements for en- closure mounting Pulling Out and Reinserting the Retractable Feet Introduction Features you’ll enjoy includeContents of the Package Introduction to the PlasmaSync 42PD2/50PD1 Setup Procedure Connect the equipment Opening the Terminal Board Cover Attaching the Remote Control HolderHousing the Remote Control in the Remote Control Holder Removing the Terminal Board Cover Part Names and Functions Front View 11 RGB3 DVI 29pin AC in connectorSide View.... Terminal Board L/R Remote Mini jack Remote Controller Visual Normal button Remote control transmitterBattery Installation and Replacement Raster Normal button Using the wired remote control mode Operating Range Making the DIP Switch Settings DIP Switch Functions and Settings Power Management Modes Power Management FunctionMode Installation Wiring Diagram Connecting Your Document Camera Connecting Your PC or Macintosh ComputerConnecting Your VCR DVD or Laser Disc Player Connections with Equipment that has a Digital Interface When using the RGB2 Input When using the Video inputsDaisy-chaining Your monitors Operation PowerAdjustment of the Display General Controls Adjustment of the screen display position Adjustment of the Display DirectAbout to Preset Raster Press Adjustment display of the left/right position Adjustment of the Image About to Preset Visual Press Adjustment of the DisplayMenu Control List of Setting Details Settings Before Making Adjustments Press the Visual Normal button or Raster Normal button About to Reset PressAutomatic Storage Align the cursor with icon Adjustment of the Image Visual ControlsBrightness Contrast Sharpness Color Tint GAMMA2 Return to the main menu Position Width Adjustment of Screen Position HorizontalAlign the cursor with the desired item Adjustment of Screen Position Vertical Position Height Color Temp High LOW User Color Temperature Color TempColor Temp Align the cursor with Color Temp and set with the / buttons Adjustment of the White Balance Gain White Level Bias Black Level Exiting the adjustment Adjustment of the On-screen Display PositionOSM H-POS OSM V-POS OSM Angle OSM Display Time Setting the On-screen Display OFF Time OSM H-POS OSM V-POS OSM Angle OSM Display Time Seconds Input Mode 4 X 3 / 16 X RGB Mode StillAdjustment of the Clock Frequency/Clock Phase Normal RGB Mode Clock phase adjustment Fine Picture Source Info RGB1 ALL Visual Normal ALL Raster Normal ALL NormalPOL.NEG POL.POS When video input is selected Source Info Video Mode NtscWhen RGB input is selected Source RGB1, RGB2, RGB3 Information Screen Timer Screen SET Timer OFFPresent Time Auto Timer Screen SET Timer on Press Proceed for Program MenuProgram Menu Date on OFF Mode Direct Daily Weekly Cursor movement Multiple Screens Setting Position DriverSetting Position Driver NO.1 Align the cursor with icon 12 on the second Align the cursor with icon 13 of the second Other Setting ScreensColor System Press the / buttons and set Gray Level SET ID no RGB3 ADJ ALL ResetBurning reduction function ID Selection Screen SET no256 Troubleshooting Symptom Checks Remedy Specifications PlasmaSync 42PD2 Model PX-42VP2A PlasmaSync 50PD1 Model PX-50VP1A Signal Identification For Raster Preset Appendix RGB Application Connections Communication Parameters Communication FormatPage Page Page Page Page Page Page Page Page Cabinet dimensions Unit inchmm