NEC 50PD1, 42PD2, 42PD2, 50PD1 user manual Appendix, Signal Identification For Raster Preset

Appendix

Signal Identification For Raster Preset

		Resolution		Factory	User	Sync polarity		Presence/absence of sync		RGB	INPUT
		(horizontal frequency/vertical frequency)		settings	settings	Hor	Ver	Hor	Ver	MODE	MODE*7
VIDEO NTSC*1				○	○	-	-			-	-
VIDEO PAL*1 VIDEO SECAM*1				○	○	-	-			-	-
640	X 240	(15.734kHz/59.94Hz)	VU-6010 NTSC*2	○	○	NEG	NEG	Y	Y	-	4 X 3
768	X 288	(15.557kHz/50.39Hz)	VU-6010 PAL*2	○	○	NEG	NEG	Y	Y	-	-
640	X 400	(31.469kHz/70.086Hz)	IBM 400@70Hz*3	○	○	NEG	NEG	Y	Y	-	-
640	X 480	(31.469kHz/59.94Hz)	VESA 480@60Hz	○	○	NEG	NEG	Y	Y	STILL	4 X 3
640	X 480	(35kHz/66.667Hz)	MAC @13''*6	○	○	-	-	-	-	-	-
640	X 480	(37.861kHz/72.809Hz)	VESA 480@72Hz	○	○	NEG	NEG	Y	Y	-	-
640	X 480	(37.5kHz/75Hz)	VESA 480@75Hz	○	○	NEG	NEG	Y	Y	-	-
640	X 480	(43.269kHz/85.008Hz)	VESA 480@85Hz*4	○	○	POS	POS	Y	Y	-	-
640	X 480	(39.375kHz/75Hz)	XGA-2 480@75Hz	○	○	NEG	NEG	Y	Y	-	-
800	X 600	(35.156kHz/56.25Hz)	VESA 600@56Hz	○	○	POS	POS	Y	Y	-	-
800	X 600	(37.879kHz/60.31Hz)	VESA 600@60Hz	○	○	POS	POS	Y	Y	-	-
800	X 600	(48.077kHz/72.188Hz)	VESA 600@72Hz	○	○	POS	POS	Y	Y	-	-
800	X 600	(46.875kHz/75Hz)	VESA 600@75Hz	○	○	POS	POS	Y	Y	-	-
800	X 600	(53.674kHz/85.061Hz)	VESA 600@85Hz*4	○	○	POS	POS	Y	Y	-	-
832	X 624	(49.725kHz/74.55Hz)	MAC @16''*6	○	○	-	-	-	-	-	-
852	X 480	(31.722kHz/59.966Hz)	I/O data wide*5	○	○	NEG	NEG	Y	Y	-	16 X 9
848	X 480	(31.02kHz/60Hz)	VGA WIDE (NEC1)	○	○	POS	POS	Y	Y	-	-
1024 X 768 (56.476kHz/70.069Hz)			VESA 768@70Hz	○	○	NEG	NEG	Y	Y	-	-
1024 X 768 (60.023kHz/75.029Hz)			VESA 768@75Hz	○	○	POS	POS	Y	Y	-	-
1024 X 768 (68.677kHz/84.997Hz)			VESA 768@85Hz*4	○	○	POS	POS	Y	Y	-	-
1024 X 768 (60.24kHz/74.93Hz)			MAC @19''*6	○	○	-	-	-	-	-	-
768	X 576	(31.389kHz/50Hz)	IDC-3000G PAL625P	○	○	NEG	NEG	Y	Y	-	-
640 X 480		(31.47kHz/59.9Hz)	IDC-3000G NTSC 525P	○	○	NEG	NEG	Y	Y	MOTION	4 X 3

*1 Convert to 640 dots x 480 lines and display.

*2 These signals cannot be displayed in the RGB3 input mode.

*3 Display only 400 lines with the screen center of the vertical orientation located at the center.

*4 The picture will be shaky when the moving images of video games, etc., are input. (In this case set the refresh rate to 75 kHz or less.) *5 Only when using an I/O DATA graphic accelerator board.

*6 Use a separately sold signal adapter (mini D-Sub 15-pin) when connecting to a Macintosh computer. For some models, make the mini D-Sub 15-pin connection using the included RGB signal cable. These signals are Sync On Green.

*7 Make the settings to display these signals. The signals will not be displayed properly unless the correct settings are made.

*The resolution deteriorates in comparison with the original image because the image of 640 dots x 480 lines is converted to 853 dots x 480 lines and displayed. *At the time of video input, video signals derived from poor recording conditions may give rise to a disturbed screen image.

*The sync may be disturbed when non standard signals other than the aforementioned are input.

*Multiple screens (2 screens) can only display signals having an aspect ratio of 4:3. *3 Cannot be used with multiple screens. *With digital inputs some signals are not accepted.

*852 dot by 480 line signals are displayed with this resolution.

*848 dot by 480 line signals are displayed at a resolution of 848 dots by 480 lines when “NORMAL” is selected, and converted to 853 dots by 480 lines when “FULL” is selected.

50