Pulling Out and Reinserting the Retractable Feet | NEC 50PD1, 42PD2

How to Attach Options to the Plasma Monitor

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

*In the upright position. (See Drawing A)

*Lay the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

This device cannot be used or installed with- out a separate Tabletop Stand or other op- tional mounting accessory. For proper instal- lation it is strongly recommended to use a trained, NEC authorized serviceman. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper instal- lation. Failure to follow these recommenda- tions could result in voiding your warranty.

Drawing A

Drawing B

Ventilation Requirements for en- closure mounting

To allow heat to disperse, leave space between surround- ing objects as shown in the diagram to the right.

Pulling Out and Reinserting the Retractable Feet

The Retractable Feet are housed at 2 locations on the bot- tom surface of the main unit.

1.Grasp the end and pull out.

2.The feet will open automatically when your hand is re- moved.

To house the Retractable Feet, close them and then continue to push them inside the main unit.

Notice:

*Installation of only the main unit is not possible. Be sure to use and install the main unit in conjunction with a stand or special unit.

Note:

RETRACTABLE FEET ARE FOR TEMPORARY USE ONLY AND ARE NOT INTENDED FOR PERMA- NENT INSTALLATION.

MODEL # PX-42VPU1-ST STAND IS REQUIRED FOR PERMANENT TABLETOP INSTALLATION. REPLACE THE FEET WHEN YOU MOVE THE MONITOR.

Wall

50mm (1.97")

31mm	31mm
(1.22")	(1.22")
	50mm (1.97")

45mm (1.77")

1 2

8

Image 8

NEC 50PD1, 42PD2 Ventilation Requirements for en- closure mounting, Pulling Out and Reinserting the Retractable Feet

Contents

User’s Manual Precautions Important Information To avoid damage and prolong operating life Mises en garde et précautions de sécurité PrécautionsDOC avis de conformation Remarque Limited Warranty Plasma Monitors What is Covered and What is not Covered Contents Ventilation Requirements for en- closure mounting Pulling Out and Reinserting the Retractable Feet Features you’ll enjoy include Contents of the PackageIntroduction Introduction to the PlasmaSync 42PD2/50PD1 Setup Procedure Connect the equipment Attaching the Remote Control Holder Housing the Remote Control in the Remote Control HolderOpening the Terminal Board Cover Removing the Terminal Board Cover Part Names and Functions Front View AC in connector Side View.... Terminal Board L/R11 RGB3 DVI 29pin Remote Mini jack Remote Controller Remote control transmitter Battery Installation and ReplacementVisual Normal button Raster Normal button Using the wired remote control mode Operating Range Making the DIP Switch Settings DIP Switch Functions and Settings Mode Power Management FunctionPower Management Modes Installation Wiring Diagram Connecting Your PC or Macintosh Computer Connecting Your VCR DVD or Laser Disc PlayerConnecting Your Document Camera Connections with Equipment that has a Digital Interface Daisy-chaining Your monitors When using the Video inputsWhen using the RGB2 Input Power Adjustment of the DisplayOperation General Controls Adjustment of the Display Direct About to Preset Raster PressAdjustment of the screen display position Adjustment display of the left/right position Adjustment of the Image About to Preset Visual Press Adjustment of the DisplayMenu Control List of Setting Details Settings Before Making Adjustments Automatic Storage About to Reset PressPress the Visual Normal button or Raster Normal button Adjustment of the Image Visual Controls Brightness Contrast Sharpness Color Tint GAMMA2Align the cursor with icon Return to the main menu Align the cursor with the desired item Adjustment of Screen Position HorizontalPosition Width Adjustment of Screen Position Vertical Position Height Color Temperature Color Temp Color TempColor Temp High LOW User Align the cursor with Color Temp and set with the / buttons Adjustment of the White Balance Gain White Level Bias Black Level OSM H-POS OSM V-POS OSM Angle OSM Display Time Adjustment of the On-screen Display PositionExiting the adjustment Setting the On-screen Display OFF Time OSM H-POS OSM V-POS OSM Angle OSM Display Time Seconds RGB Mode Still Adjustment of the Clock Frequency/Clock PhaseInput Mode 4 X 3 / 16 X Normal RGB Mode Clock phase adjustment Fine Picture POL.NEG POL.POS ALL Visual Normal ALL Raster Normal ALL NormalSource Info RGB1 Source Info Video Mode Ntsc When RGB input is selected Source RGB1, RGB2, RGB3When video input is selected Information Screen Present Time SET Timer OFFTimer Screen SET Timer on Press Proceed for Program Menu Program Menu Date on OFF ModeAuto Timer Screen Direct Daily Weekly Cursor movement Setting Position Driver Setting Position Driver NO.1Multiple Screens Align the cursor with icon 12 on the second Other Setting Screens Color SystemAlign the cursor with icon 13 of the second Press the / buttons and set Burning reduction function RGB3 ADJ ALL ResetGray Level SET ID no 256 SET noID Selection Screen Troubleshooting Symptom Checks Remedy Specifications PlasmaSync 42PD2 Model PX-42VP2A PlasmaSync 50PD1 Model PX-50VP1A Signal Identification For Raster Preset Appendix RGB Application Connections Communication Parameters Communication FormatPage Page Page Page Page Page Page Page Page Cabinet dimensions Unit inchmm