USER MANUAL
ENGLISH
TROUBLESHOOTING
Trouble | Possible cause | Remedy | |
|
|
| |
| The hood (13) is not properly closed. | Close the hood properly. | |
|
|
| |
| The engine oil level is too low. | Check that the engine oil level is within the limits. (*) | |
|
|
| |
The engine does not start with the ignition | The machine has run out of fuel. | Check that there is fuel in the tank (30). | |
key. |
|
| |
The fuel does not reach the carburettor. | Check that the fuel reaches the carburettor and that | ||
| |||
| the fuel filter is clean. (*) | ||
|
| ||
|
|
| |
| The spark plug does not produce a spark. | Check that the spark plug produces a spark. (*) | |
|
|
| |
| The engine oil level is too low. | Check that the engine oil level is within the limits. (*) | |
|
|
| |
The engine stops during operation. | The machine is running out of fuel. | Check that there is fuel in the tank (30). | |
|
|
| |
| The fuel filter is dirty. | Clean the fuel filter. (*) | |
|
|
| |
| The vacuum system is turned off. | Turn on the vacuum system with the switch (56). | |
|
|
| |
| The dust filter is clogged. | Clean the dust filter. | |
|
|
| |
The machine collects little debris/dust. | The hopper is full. | Empty the hopper (4). | |
|
| ||
The skirts are not integral or not properly | Check the skirts (16, 17, 18, 19) for integrity and | ||
| |||
| adjusted. | proper adjustment. | |
|
|
| |
| The broom height is not properly adjusted. | Adjust the height of the brooms (10, 11, 12). | |
|
|
| |
| The parking brake is engaged. | Check that the parking brake (84 and 76) has been | |
| released. | ||
|
| ||
When pressing the drive pedal, the | The hydraulic system oil level is incorrect. | Check the hydraulic system oil level in the tank (28). | |
machine does not move, or it moves |
|
| |
The centrifugal pulley does not operate | Check that the centrifugal pulley (petrol | ||
slowly. | |||
| properly. | pump coupling joint) operates properly. (**) | |
| The drive pedal is not properly adjusted. | Adjust the drive pedal. (**) | |
|
|
| |
The hopper does not lift. | The hydraulic system oil level is incorrect. | Check the hydraulic system oil level in the tank (41). | |
|
| ||
The F4 or F7 fuse is open. | Replace the fuse. | ||
| |||
|
|
| |
The hopper does not dump. | The F7 fuse is open. | Replace the fuse. | |
|
| ||
The hopper is not lifted enough. | Lift the hopper over 300 mm. | ||
| |||
|
|
| |
| The hopper has not returned to horizontal | Turn the hopper to horizontal position. | |
| position. | ||
|
| ||
The hopper does not lower. | In case of particular weather conditions, the | Wait a few moments to let the hydraulic system oil | |
| hydraulic system oil is slow in flowing through | ||
| flow. | ||
| the safety valve. | ||
|
| ||
|
|
| |
When the engine compartment hood (13) | The hood safety microswitch does not work. | Repair the microswitch. (**) | |
is open, the engine keeps running. | |||
|
|
(*)For the relevant procedure, see the Petrol Engine Manual. (**) Procedure to be performed by Nilfisk Alto Service Center.
For further information, refer to the Service Manual, available at any Nilfisk Alto Service Center.
FLOORTEC R 680 P |
31