First Time Setup
This section explains the settings that you need to make before using the AV receiver for the very first time.
Speaker Settings
| 4 |
| 5 |
| 6 |
|
| - |
| |
If you change these settings, you must run the auto- | ||||||||||
| TAPE | TUNER | CD |
|
|
|
| |||
| 7 |
| 8 |
| 9 |
|
|
|
| |
matic speaker setup again (see page 61). |
| |||||||||
| PHONO | NET/USB | D. TUN | TV VOL |
| |||||
| +10 |
| 0 | CLEAR |
|
| ||||
|
|
| 11 |
|
|
| 12 |
|
| |
| INPUT SELECTOR |
|
|
|
|
| ||||
|
| MACRO |
|
|
|
|
|
| ||
| 1 |
| 2 |
| 3 |
|
| ZONE3 |
| |
|
| REMOTE MODE |
|
|
| |||||
| DVD | VCR | CD |
|
| ZONE2 |
| |||
|
|
|
|
| CDR/MD/DOCK |
| 1 | |||
| TV | CABLE | NET/USB | RECEIVER | ||||||
|
| SAT |
|
|
|
| TAPE/AMP | |||
| DIMMER |
|
|
|
|
|
|
| SLEEP |
|
2, 3 |
|
|
| ENU | M | EN |
|
|
| |
|
| M |
| U |
| |||||
|
| OP |
|
|
|
|
|
| ||
|
| T |
|
|
|
|
|
|
|
|
| + |
|
|
|
|
|
|
|
|
|
| CH |
|
| ENTER |
|
|
| VOL |
| |
| DISC |
|
|
|
|
|
| |||
| ALBUM |
|
|
|
|
|
|
|
|
|
1, 6 | - |
| G |
|
|
|
|
|
|
|
|
| UIDE | IT |
|
|
|
| |||
PREV |
|
| EX |
|
|
|
| |||
SE | T | UP | RE |
| N |
|
| |||
| CH |
|
|
| TU |
|
|
| ||
| DISPLAY |
|
|
|
|
|
|
| MUTING |
|
| REC |
|
| PLAYLIST |
|
|
| RANDOM |
|
If the impedance of any speaker is 4 ohms or more but less than 6, set the Speaker Impedance to 4 ohms.
To use
Notes:
•When bridging is used, the AV receiver is able to drive up to 2.1 speakers in the main room.
•When
•Before you change these settings, turn down the vol- ume.
The onscreen menus shown in this manual may be slightly different from what you see on your TV.
1 | Press the [RECEIVER] button, | |
| ||
RECEIVER | followed by the [SETUP] button. | |
| The main menu appears onscreen. | |
S |
| |
E |
| |
T |
| |
UP |
| |
2 | Use the Up and Down [ ]/[ ] | |
| buttons to select “2. Speaker | |
ENTER | Setup,” and then press [ENTER]. | |
The Speaker Setup menu appears. | ||
|
3 | Use the Up and Down [ | ]/[ ] |
| buttons to select “1. Speaker Set- | |
| tings,” and then press [ENTER]. | |
| ENTER |
|
| The Speaker Settings menu appears. | |
|
| |
| Speaker Impedance | 6ohms |
| Front(Speaker A) | Normal |
| Front(Speaker B) | Not use |
| ENTER |
|
4 | Use the Up and Down [ ]/[ ] |
| buttons to select “Speaker |
Impedance,” and use the Left and
ENTER
Right []/[ ] buttons to select:
4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6.
6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms.
5 | Use the Up and Down [ ]/[ ] |
| buttons to select “Front (Speaker |
A),” and use the Left and Right
ENTER
[]/[ ] buttons to select:
Normal: Select this if you’ve con- nected your front Speakers A normally.
BTL: Select this if you’ve con- nected your front Speakers A for bridged operation. The BTL indicator will appear on the display.
Note:
•
ENTER
51