Panasonic AJ-HD3700BE, AJ-HD3000, AJ-HD2000, AJ-HD2700 manual DLY Strt, FD TIME2, MODE2, Cut, Fade

INSERT/ASSEMBLE AUTO EDIT SET UP menu

Key	Key designation		Description
F8	EXIT	Returns the VTR to the AUTO EDIT menu screen.
F9	DLY STRT	Sets the timing after the playback command was issued until the
	Delay start.	actual operation in 1-frame increments. (This is used to facilitate
		the synchronization with another VTR which has a different servo
		reference.)
		The timing can be set from j30 frames to i30 frames°1 in
		1-frame increments. (Initial setting is 0 frame.) (With a “j” value,
		the operation is performed earlier, and the preroll time is
		compensated for in the LOCAL mode. With a “i” value, the
		operation is performed later, and it takes effect both in the
		REMOTE and LOCAL modes.)
F10	TRACKING	At normal times, tracking adjustment is not necessary. Adjustment
	For adjusting the tracking.	is made if tracking disparities have occurred during editing.
		VAR:	The tracking can be adjusted manually.
			Refer to “Manually adjusting the tracking” (on page 106).
		FIX:	The tracking is fixed.
		OPT. ONCE: At the initial editing after the cassette has been
			inserted, the tracking is optimized while the tape is
			playing back up to the IN point. The tracking is not
			subsequently optimized. Tracking can be optimized
			again. Refer to “Automatically adjusting the
			tracking” (on page 105). When the PLAY button
			and STAND BY button are pressed together during
			EDIT/PLAY, the tracking is optimized again, and it
			is optimized with each EDIT/PLAY operation.
		OPT. AUTO: The tracking is optimized while the tape is playing
			back up to the IN point with each editing operation,
			and it is retained even if the VTR is transferred to
			another menu. Refer to “Automatically adjusting the
			tracking” (on page 105).
F11	CAP LOCK	For selecting the capstan servo lock mode during playback.
	For setting the capstan	4F AUTO (8F AUTO: 1080/23p, 1080/24p, 1080/25p, 1080/50i, 576/50i):
	servo lock.	Assumes the color frame auto lock mode. If discontinuity is
		produced in the color frame during playback, the unit locks again
		to a new color frame.
		4F FORCE (8F FORCE: 1080/23p, 1080/24p, 1080/25p, 1080/50i, 576/50i):
		Assumes the color frame forced lock mode. If there is any
		discontinuity in the color frame during playback, the unit
		preserves the field sequence at initial lock.
		2F: Assumes frame lock mode.
		≥The capstan servo lock mode can be set in HOME SET UP menu.
		If the two settings differ, priority is given to the final mode setting.

F12	FD TIME°2
	For setting the audio fade
	time.

Valid when the F13 key is set to X FADE or V FADE.

The times that can be set are as follows: 5, 10, 15, 20, 25, 50, 100 ms. (Initial setting is 5 ms.)

For the setting procedure, refer to “Setting the audio fade time” (on page 107).

F13	MODE°2	Audio editing can be accomplished while cross-fade editing prior
	For selecting audio fade	playback audio and input audio or V-fade editing.
	editing.	X FADE: Performs audio cross-fade editing.
		CUT:	Performs cut (normal) editing.
		V FADE:	Performs audio V-fade editing.

°1This range differs depending on the format used.

°2Only CUT can be selected when TAPE has been selected as the EDIT REC STATE setting. However, FADE can be selected by pressing this key and F key together, in which case the EDIT REC STATE setting is switched to EE1.

– 119 –