Warning System
Warning Description Tables
If a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the WARNING lamp, lamps inside the viewfinder and a warning tone.
Note
The WARNING lamp has the highest priority, followed by the tally lamp, and then the warning tone. When multiple errors occur simultaneously a higher priority indication will be triggered. The
1. System Errors
Display window | The error code lights up. | |
indication | ||
| ||
|
| |
WARNING lamp | Blinks 4 times per second. | |
|
| |
Tally lamp | Blinks 4 times per second. | |
|
| |
Viewfinder | The “SYSTEM ERROR” indication and | |
the error code light up. | ||
| ||
|
| |
Warning tone | Beeps continuously. | |
|
| |
Warning description | An error in the reference signal or the | |
communication. | ||
| ||
|
| |
Recording/playback | The operation stops. | |
operation | ||
| ||
Countermeasures | Please confirm [Error Codes] (page 158) | |
and consult your distributor. | ||
| ||
|
|
2.Card removal error
Display window | Error code | |
indication | ||
| ||
|
| |
WARNING lamp | Blinks 4 times per second. | |
|
| |
Tally lamp | Blinks 4 times per second. | |
|
| |
Viewfinder | The “TURN POWER OFF” indicator lights | |
up. | ||
| ||
|
| |
Warning tone | Continues to beep. | |
|
| |
Warning description | The P2 card being accessed has been | |
removed, resulting in an error in the | ||
| internal memory of the unit. | |
|
| |
Recording/playback | Cannot be performed. | |
operation | ||
| ||
Countermeasures | Turn off the power to the unit. If there is | |
an error in a clip on the removed P2 card, | ||
| repair the clip. | |
|
|
3. Battery Empty
Display window | All 7 bar indicators for battery remaining | |
indication | capacity start blinking. | |
|
| |
WARNING lamp | Lights up. | |
|
| |
Tally lamp | Blinks once per second. | |
|
| |
Viewfinder | The BATT LED lights up. | |
|
| |
Warning tone | Beeps continuously. | |
|
| |
Warning description | The battery has run out. | |
|
| |
Recording/playback | The operation stops. | |
operation | ||
| ||
Countermeasures | Replace the battery. | |
|
|
4.P2 Card Fully Recorded
Display window | All 7 bar indicators for remaining MEDIA |
|
|
indication | capacity start blinking. |
|
|
| |||
|
|
|
|
WARNING lamp | This lamp will illuminate continuously until |
| Maintenance |
an operation is made after recording. |
| ||
|
| ||
|
|
| |
Tally lamp | This lamp will flash 4 times every second |
| |
|
| ||
until an operation is made after recording. |
|
| |
|
|
| |
|
|
|
|
Viewfinder | The “END” indicator blinks. |
|
|
When a write protected P2 card has been |
|
| |
| inserted, the “WP” indicator lights up. |
| and |
|
|
| |
Warning tone | This tone will sound continuously until an |
| |
operation is made after recording. |
| Inspections | |
|
| ||
|
|
| |
Recording/playback | The recording stops. |
| |
Warning description | The P2 cards are recorded to maximum |
|
|
| capacity. |
|
|
operation |
|
|
|
|
|
|
|
Countermeasures | Delete the clips in the P2 card or insert a |
|
|
new P2 card. |
|
| |
|
|
| |
|
|
|
|
5.Image Sequence Error (24P, 30P, 25P)
Display window | ||
indication | field. | |
|
| |
WARNING lamp | Blinks 4 times per second. | |
|
| |
Tally lamp | Blinks 4 times per second while recording | |
continues. | ||
| ||
|
| |
Viewfinder | The “REC WARNING” indicator lights up. | |
|
| |
Warning tone | Beeps 4 times per second while recording | |
continues. | ||
| ||
|
| |
Warning description | There are abnormal conditions in the | |
image sequence of the 24P, 30P, or 25P | ||
| mode. | |
|
| |
Recording/playback | Images can be recorded and played | |
back, but some frames may be dropped | ||
operation | ||
or the sequences of TC and UB may shift. | ||
| ||
|
| |
| Confirm the recording/playback operation | |
Countermeasures | after turning off the power supply once | |
and then turning it on again. If the error is | ||
| not corrected after executing this | |
| procedure, contact the dealer. | |
|
|
Maintenance and Inspections: Warning System 155